1) two-stage heat treatment
双温热处理
1.
On the basis of the previous experiment, to take the optimum single temperature heat treatment as a comparison the harvested broccoli were instead treated by different combinations of two-stage heat treatment.
本研究在单温热浸处理采后西兰花研究的基础上,以前期实验结果最佳单温热浸处理为对照,采用不同双温热处理组合热浸处理采后西兰花,在商业贮运温度条件(5℃)下贮藏10d,转到货架温度条件(20℃)下贮藏3d后,进行保鲜品质、黄化率、霉斑率、叶绿素含量、细胞膜透性和过氧化物酶活性等测定。
2) heat treatment temperature
热处理温度
1.
Effects of heat treatment temperature on the preparation of nanometer TiO_2 by melt-phase separation process;
热处理温度对熔融分相法制备纳米TiO_2影响的研究(英文)
2.
Study on heat treatment temperature of EMD used for Li-MnO_2 batteries;
Li-MnO_2电池用EMD热处理温度的研究
3.
Influence of heat treatment temperature after the pressure expansion on the electromechanical properties of cellular polypropylene electret;
压力膨化后的热处理温度对PP蜂窝膜驻极体机电性质的影响
3) isothermal heat treatment
等温热处理
1.
Effects of isothermal heat treatment on microstructure and mechanical properties of lost foam casting AZ91D magnesium alloy;
等温热处理对消失模铸造AZ91D镁合金组织与性能的影响
2.
Effects of SiC on microstructure of AZ91D alloy during isothermal heat treatment
SiC对等温热处理AZ91D镁合金组织的影响
3.
6Al10Nb5 bulk amorphous alloy with isothermal heat treatment have been studied by X-ray diffractometer,scanning electronic microscope,micro-hardness tester and compression experiment.
6Al10Nb5块体非晶合金进行了等温热处理,用X射线衍射仪、扫描电镜、显微硬度计与压缩试验机研究了不同温度下的等温热处理后合金的组织结构变化、硬度变化与压缩性能变化。
4) high temperature treatment
高温热处理
1.
Study on the effects of high temperature treatment on performance of C/C composites;
高温热处理与C/C复合材料性能关系研究
2.
Effect of high temperature treatment on properties of polyimide films;
高温热处理对聚酰亚胺薄膜性能的影响
3.
The effects of different carbon coatings and high temperature treatment on the flexural strength and fracture modes of C/C-SiC composites were studied.
以针刺整体炭毡为坯体 ,采用CVD和树脂浸渍 /炭化混合法增密制备了 4种C/C多孔体 ,然后熔硅浸渗C/C多孔体制备了C/C SiC复合材料 ;研究了不同炭涂层、高温热处理对C/C SiC复合材料弯曲强度和断裂方式的影响。
5) heating temperature
热处理温度
1.
The influences of precursor,oxygen pressure and heating temperature on the microstructure and properties of the thin films have been discussed.
综述了采用软化学方法制备VO2薄膜的工艺技术特点,以前驱物的划分为主线,着重探讨了前驱物的选择、氧分压和热处理温度等工艺条件对其物相结构与性能的影响,对反应热力学进行了初步的探讨。
6) isothermal heat-treatment
等温热处理
1.
%Pb alloy was studied by isothermal heat-treatment.
结果表明 :在等温热处理过程中 ,等温温度为 193℃等温时间为 6 0分钟时 ,其电导率σ约为 0 。
2.
8Zn alloy were investigated during semi-solid isothermal heat-treatment.
8Zn镁合金在半固态等温热处理过程中,等温温度和等温时间对其组织和力学性能的影响。
补充资料：2,2-双氯甲基-三亚甲基-双[双(2-氯乙基)磷酸脂]
CAS：38051-10-4
分子式：C13H24Cl6O8P2
中文名称：2,2-双氯甲基-三亚甲基-双[双(2-氯乙基)磷酸脂]
英文名称：2,2- bis(chloromethyl)-trimethylene bis[bis(2-chloroethyl)phosphate]
phosphoric acid, 2,2-bis(chloromethyl)-1,3-propanediyl tetrakis(2-chloroethyl)
2,2-bis(chloromethyl)trimethylene bis(bis(2-chloroethyl)phosphate)
2,2-bis(chloromethyl)-1,3-propanediyltetrakis(2-chloroethyl)phosphate
分子式：C13H24Cl6O8P2
中文名称：2,2-双氯甲基-三亚甲基-双[双(2-氯乙基)磷酸脂]
英文名称：2,2- bis(chloromethyl)-trimethylene bis[bis(2-chloroethyl)phosphate]
phosphoric acid, 2,2-bis(chloromethyl)-1,3-propanediyl tetrakis(2-chloroethyl)
2,2-bis(chloromethyl)trimethylene bis(bis(2-chloroethyl)phosphate)
2,2-bis(chloromethyl)-1,3-propanediyltetrakis(2-chloroethyl)phosphate
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条