1) latex particle
乳胶粒
1.
Through the analysis of ultraviolet spectroscopy, it is found out that the absorbance of the latex particles is highe.
通过“粒子设计”利用核壳乳液聚合技术以功能型紫外线吸收剖、苯乙烯、丙烯酸丁酯、甲基丙烯酸甲酯、丙烯酸乙酯为单体制备出核壳结构的聚合物乳胶粒。
2.
The mechanism of latex particle formation and its transformation during anionic emulsion polymerization was studied, while DBSA was used as catalyst and emulsifier.
分析实验现象发现,该体系中羟基硅油乳胶粒是通过胶束和单体珠滴两种方式形成的,由单体珠滴生成的体积较大的羟基硅油乳胶粒是形成羟基硅油乳液“漂油”的主要原因。
3.
The occupied area (Am)of a sodium dodecyl benzene sulphonate(SDBS) molecule adsorbed on PEA latex particles and the covered area ratio on particle surfaces under various surfactant contents were measured.
测定了乳化剂十二烷基苯磺酸钠(SDBS)分子在聚丙烯酸乙酯(PEA)乳胶粒表面的覆盖面积A_m和不同乳化剂用量下胶乳的表面覆盖率φ。
2) emulsion particle
乳胶粒
1.
In this paper,the emulsoid particle′s size and weight distribution of core-shell emulsion were estimated,and it′s result was compared and analyzed with other emulsions,the conclusion is core-shell emulsion particle′s size is most small and distribution is most uniform.
对核壳结构聚合物乳液乳胶粒的粒径及其分布进行了测试 ,并与同一聚合物体系的其它乳液加以比较、分析 ,得出其粒径最小、分布最均匀的重要结
3) PSA-A latex
PSA-A乳胶粒
1.
In this paper,anionic PSA-A latex particles can be coated with hydrate CeO2 by aging the solution containing PSA-A,urea,and Ce(SO4)2.
以PSA-A乳胶粒为模板,通过硫酸高铈和尿素的水解反应得到PSA/水合CeO2的核/壳结构的复合微球,通过煅烧除去乳胶粒模板得到立方相CeO2空心微球。
4) latex particle
乳胶粒子
1.
Calculation of force acting on flexing and deforming latex particle in oil
油液对伸缩变形乳胶粒子作用力的计算
2.
The fundamental morphologies of core/shell latex particle and common characterization methods were presented.
介绍了核壳型乳胶粒子的基本形态结构和常用的表征手段,详细说明了用透射电子显微镜(TEM)表征核壳型乳胶粒子结构的两种情况,即分析透射电子显微镜法、普通透射电子显微镜法(免染色法和选择性染色法),并给出了它们的适用范围。
3.
It is found that the latex particle has core-shell structure, the glass transition temperat.
透射电镜观察证实了此乳胶粒子的形态特征,表征了共聚物的玻璃化转变温度及薄膜的拉伸强度和吸水率。
5) latex particle size
乳胶粒径
1.
The effects of amount and composition of composite emulsifiers and of redox initiators on latex particle size were discussed by orthogonal experiment and homogeneous design experiment respectively.
研究了醋酸乙烯酯 /丙烯酸丁酯 /丙烯酸三元共聚合乳液的合成工艺条件 ,应用正交实验和均匀实验设计得出了乳化剂用量及配比 ,氧化 -还原引发剂用量及配比对乳胶粒径的影响 ,乳化剂及体系 p H值对乳液稳定性的影响 ;采用间歇法聚合工艺 ,当乳化剂用量为 7。
6) EVA Latex Particles
EVA乳胶粒
补充资料：牛柳粒炒杂菜粒
牛柳粒炒杂菜粒
原料：牛肉半斤、杂菜粒一包.
佐料：盐、糖、酱油、黑椒粉(可因个人口味增减)、油、蒜茸(同黑椒粉)、鸡粉。
过程：
1．将牛肉切粒，若不善刀工者可在市场买的时候就请人代劳。用酱油、油、糖、生粉捞一捞。
2．用少少的油热一下锅，爆香蒜茸；
3．将牛肉粒倒进锅里，中火翻炒一分钟，加入黑椒粉、鸡粉，看牛肉转了颜色就可以装出来，不然牛肉会炒老；
4．不用再加油了，倒入杂菜粒(事先要过水)，翻炒一分钟，加一点盐；
5．加入牛肉粒再翻炒1-2分钟；
6．大功告成，上盘。
温馨提示
杂菜粒在一些比较大型的超市里会有配好一包一包售卖的，可以挑选自己喜欢的口味，做菜前只需将其用开水泡一泡就可以了。油不用放得太多，只在开始放上两锅铲就够了，以健康为主。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。