1) precipitate strengthened austenite alloys
沉淀强化奥氏体合金
1.
Discrete Variational Method (DVM) was adopted in the first principles calculation of hydrogen occupation between γ and γ′ in precipitate strengthened austenite alloys to analysis the mechanism of hydrogen embrittlement of them.
本文针对沉淀强化奥氏体合金氢脆通常较单相奥氏体严重这一点,采用离散变分方法对氢在沉淀强化奥氏体合金中γ基体与γ′相之间占位进行了第一原理计算和分析。
2) austenitic precipitation hardening stainless steel
奥氏体沉淀硬化不锈钢
3) high strength austenitic alloy
高强度奥氏体合金
5) austenitic alloy
奥氏体合金
1.
Effect of last heat forging deformation degree on mechanical properties of FeNi-based austenitic alloy;
锻造变形量对FeNi基奥氏体合金力学性能的影响
2.
Corrosion mechanisms of a new-type high-manganese austenitic alloy in a molten zinc bath
新型高锰奥氏体合金耐液锌的腐蚀机理
3.
This paper analyzes and compares the ends of the brittle delay fracture and hydrogen brittleness of Austenitic alloy, and reveals their difference and relation.
通过对奥氏体合金脆性延迟断裂和氢脆断口的分析和比较,揭示了它们之间的区别和联系,提出了奥氏体合金应力腐蚀断裂与氢脆的机理。
6) alloyed austenite
合金奥氏体
1.
Atom state ascertainment factor ω is used to determine the hybridization states of atoms in Fe-CMe unit cell of alloyed austenite.
本文以一元合金奥氏体为研究对象,应用原子状态判定因子w来确定Fe-C-Me晶胞中各原子的杂化状态。
补充资料:沉淀强化
沉淀强化
precipitation strengthening
在时效温度下随时间而变化的现象。是20世纪初首先在铝合金中发现的。它是提高材料强度最有效的方法,是铝合金和高温合金的主要强化手段。沉淀强化的基本条件是固溶度随温度下降而降低。 沉淀颗粒的存在对位错运动起障碍作用,因而提高材料对塑性变形的抗力。位错与沉淀颗粒的交互作用很复杂,但可以按几种不同的机制来描述。 奥罗万绕越机制在外加切应力作用下,基体中的运动位错线遇到沉淀相粒子时,位错线在粒子间产生弯曲,弯曲的最小曲率半径为 r Pmln一万石式中r是伯氏矢量为b的位错的线张力,r为外加切应力。当滑移面上粒子间距L)ZPmln时,位错线能在粒子之间绕越过去,并且在颗粒周围留下小位错环。位错环造成的切应力增量为 △r一Gb/L式中G为切变弹性模量。按照位错绕越机制,析出强化效果与颗粒间距成反比。合金的流变应力与析出颗粒的性质无关。这个机制适用于沉淀相颗粒较大、强度较高和间距较宽的情形。相反,当析出粒子间距小于Pmln时,位错不能绕越过去,只能切割颗粒而通过。在这种情况下,合金的流变应力或屈服强度取决于位错与颗粒间的相互作用,与颗粒性质有很大关系。 化学强化当位错剪切颗粒时,将会产生一个附加的颗粒一基体界面,这需要消耗单位面积为rs的能量。假设颗粒为球状,平均半径为<价,体积百分数为f,则化学强化的大小为 r=(6 rsabf/尤厂)“2
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条