1) loading method
加载方式
1.
The influence of loading method(such as static loading,cyclic loadi ng,dynamic loading)on fatigue behaviour of Si 3 N 4 material was studied systemly.
系统研究了加载方式(静载荷、循环载荷、动载荷)对Si3N4陶瓷疲劳特性的影响。
2.
Concerning the specialty of the testing of stressed skin diaphragm assembly,the current loading method of cantilever beam test is improved by the diagonally loading method.
考虑受力蒙皮组合体试验的特殊性,对普遍采用的悬臂梁式加载方式进行了改进,提出沿对角线加载的方法。
3.
Experimental research on influence of four types of loading methods on behaviors of CFST long columns and mid-long columns subjected to axial loads is carried out.
进行4种加载方式对钢管混凝土轴压长柱和中长柱试件受力性能影响的试验研究,并与轴压短柱试验进行对比和分析。
2) loading mode
加载方式
1.
The influence of loading mode on the necking of viscous media under outer pressures
加载方式对黏性介质外压缩径成形的影响
2.
In the case of the movable die, two different loading modes are treated in the experiments.
为了研究可移动凹模对板材液压成形的影响,进行了有无可移动凹模与不同可移动凹模加载方式(方式1与方式2)的板材液压成形试验。
3.
The fracture morphology of cast iron is influenced mainly by its internal crystal structure and loading mode.
铸铁断口形貌主要受其内部结晶组织和加载方式的影响。
3) loading way
加载方式
1.
In this paper,testing methods are presented based on the analysis of different loading ways and testing results are also given through experiments.
摩擦系数测试设备是获得跑道摩擦系数的关键设备,而如何获得进行摩擦系数计算的摩擦力和正压力成为研究的重点,在分析不同加载方式的基础上,给出了测试方法,并进行了试验。
2.
In order to improve the accuracy and precision of Rockwell hardness tester,and meet the requirements of high-precision hardness measurement,the loading way of Rockwell hardness tester is changing gradually to the dynamoelectric loading way.
为提高洛氏硬度计测量的准确性和精度,更好地满足高精度硬度测量的要求,洛氏硬度计的加载方式正逐步向电动加载转变。
4) loading conditions
加载方式
1.
Based on the experimental study of 27 lightweight aggregate concrete filled steel tube(LACFST) stub columns under three types of loading conditions,influence of the loading conditions on the failure pattern and mechanical behavior of the specimens are studied.
采用3种加载方式对27根钢管轻集料混凝土短柱进行轴压试验,分析了加载方式对构件轴心受压破坏形态和力学性能的影响,主要试验参数为不同轻集料混凝土强度等级和钢管截面尺寸。
5) Loading condition
加载方式
1.
Methods:Using three dimensional finite element method(3-D FED),simulating five bite states,putting five loading conditions on 3-D FED model of maxillary complete denture with three different palatal vault shape.
结果:3种腭穹隆形态上颌全口义齿基托在5种加载方式下,凹型腭穹隆形态基托的上腭前部及后缘区向黏膜组织的下压位移最大,基托边缘封闭区背离黏膜组织的位移最小。
2.
In this paper,the effects of billet optimization and loading conditions on the forming quality during titanium alloy bulkhead isothermal closed-die forming process have been investigated,based on the rigid-viscoplastic finite element code,DEFORM-3D.
针对这些成形缺陷,基于DEFORM有限元软件,采用数值模拟方法研究钛合金等温闭式模锻成形过程坯料和加载方式优化对锻件成形质量的影响。
6) DSP Boot
DSP加载方式
补充资料：油气田开发方式(见油气田生产方式)
油气田开发方式(见油气田生产方式)
development pattern of oil and gas field:see recovery pattern of oil and gas field
a垃d gas月e卫d) 、‘。尸卫Jlent见油气田小冰、*pa士teroof ojl
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条