说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 设备尺寸
1)  size of equipment
设备尺寸
1.
It is described in detail how to determine the technological parameter and size of equipment, such as rotary drum, induced draft fan, circular bag type dust collector.
详细介绍冷却转筒、引风机 ,圆布袋除尘器工艺参数及设备尺寸的确定。
2)  installation dimension
安装[设备]尺寸
3)  additional size
备用尺寸
1.
Determination method of additional size for protective coal pillar under deep coal mining conditions;
深部开采条件下保护煤柱备用尺寸的确定方法
4)  stock size
储备尺寸
5)  size and equipment of longwall coal mining face
工作面尺寸及设备
6)  dimension design
尺寸设计
1.
In the dimension design of coal pillars in strip mining,presently,most of them are carried out by analyzing strength stability,without considering the effect of weak plane in coal pillar.
针对在条带开采煤柱尺寸设计中大多数是采用强度稳定性分析的方法,而没有考虑弱面对煤柱稳定性的影响,由于弱面的存在,煤柱常常会因抗剪强度不够而产生剪切破坏等问题。
2.
on the basis of Lest squres solution,its dimension design linear equations were set up.
提出了一种钳口作平动的钳子 ,基于最小二乘法建立了该种钳子尺寸设计的线性方程组 ,通过三维动画与试制验证了设计的正确
3.
on the dimension design of coal pillars in strip mining, presently, most of them are carried out by analyzing strength stability, without considering the effect of weak plane in coal pillar, in fact ,coal pillars with weak plane are often damaged, because the shear strength is not enough.
在条带开采煤柱尺寸设计中,目前大多数是采用强度稳定性分析的方法,而没有考虑弱面对煤柱稳定性的影响。
补充资料:工程图标准尺寸及坐标尺寸

标准标注类型,是我们常用的标注类型。而坐标标注是便于数控加工采用的另一中标注形式。PRO/E可以将两种标注方式进行转换。


· 3.2 标准标注到坐标标注的转换


注意: 转化为坐标标注的尺寸必须是线性标注的,下列尺寸不能转化为坐标标注:


 



  • 被显示成线性尺寸的直径
  • 中心线尺寸

 



  1. 选择MODIFY DRAW > Dim Params > Dim Type > Ordinate Dim > Create Base.
  2. 选择作为参考基准线的尺寸
  3. 选择基准的引出线,该点为0点
  4. 选择 MOD DIM TYPE > Lin to Ord .
  5. 选择线性尺寸:注意:必须选择具有相同基准的尺寸

========>>>>

· 3.3 由坐标标注到标准标注的转化

1. 选择 DIM PARAMS > Diam Dim Type .


2.点击Ord to Lin


3.选择尺寸即可

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条