1) wall compressive strength
壁面抗压强度
3) Veneer compressive strength
贴面抗压强度
4) compressive strength
抗压强度
1.
Effect of the size and the proportion of gas coal and coal-char on the consist-compressive strength of formed coke;
煤料的粒度对型焦抗压强度的影响
2.
Influence of pressure head roughness upon compressive strength and test result dispersion of single crystal diamond;
压头粗糙度对金刚石抗压强度及单颗粒测量值离散性的影响
3.
Relation between compressive strength and fractal dimensions of jointed rock-mass;
节理岩体分形维数与抗压强度的关系探讨
5) compression strength
抗压强度
1.
Study on relationship between particle size distributional fractal dimension of cement particles and compression strength of cement mortars;
水泥颗粒粒度分布分形维与其胶砂抗压强度的关系研究
2.
Discussion on notation about compression strength σ_d of metallic powder;
金属粉末抗压强度σ_d值表示法的探讨
3.
Study on the influence factors of compression strength of coking coal slime briquette;
影响炼焦煤煤泥型煤的抗压强度因素研究
6) strength
[英][streŋθ] [美][strɛŋθ]
抗压强度
1.
Effects of the Number of Firing on Strength of Nano-ceramic and Traditional Ceramic in Metal-ceramic Crown Prosthsis;
烧结次数对纳米陶瓷与普通陶瓷金瓷冠抗压强度影响的对比研究
2.
Microstructures of the sintered specimens were examined by scanning electron microscopy and their strengthes and average coefficients of thermal expansion were tested.
对这些材料分别进行抗压强度测试 ,用扫描电镜观察了显微结构 ,测定了室温 - 10 0 0℃的平均线膨胀系数。
3.
Experiments show that the workability,the amount of cement and fine aggregate and the mechanical strength of concrete are influenced with the addtion of the fly-ash.
简明介绍了包头地区粉煤灰的成分和特点 实验表明,粉煤灰掺入后对混凝土的和易性、骨料、水灰比和最终抗压强度都有所改善 粉煤灰对提高混凝土的塌落度有明显作用,可以减少水泥和细骨料的比例等 水泥用量不变时,加入适量粉煤灰可以提高混凝土最终抗压强度 实验表明,包头地区粉煤灰完全可以在混凝土工程中应
补充资料:焦炭抗压强度
焦炭抗压强度
compressive strength of coke
Jiaotan kangya qiangdu焦炭抗压强度(eompressive Strength。f coke) 焦炭在压力作用下断裂时,其单位面积上承受的力,即焦炭断裂时所能承受的最大压应力。它是反映焦炭力学性质的一项指标。试验是在恒定的应变速度下,对圆柱体焦样轴向加载,直至焦样断裂。其抗压强度叮一磊,Pa。式中尸为焦样断裂时所加的载荷,N;R为焦样截面半径,m。焦炭在轴向压力下的应变曲线大致分成四个区域。(见图)朋为初始区,焦炭在较低的轴向压力下,由于开气孔的闭合而发生较明显的应变,这是多孔材料的应变特征;贸为弹性区,应力- 训帕叮一__ 了:一。、一」/爪、_、一}川才z刀℃’} L一_匕一___~‘J___~___~~--一~~~砂 二、、.,.):‘上51}‘〕 位移,口们 室温下焦炭轴向压缩时的玉力一位移图应变近似于线性关系,c点为轴向压力达到的最大值;cD为脆性区,由于裂纹扩展,试样因受压而积蓄的能量被释放出来,但未达到破碎;DE为临界区,这时轴向力稍有增加,试样就产生很大的应变,并导致裂纹扩展。抗压强度试验是在材料试验机上进行的。一般焦炭试样制成直径约巧~、长约23~的圆柱体,型焦则用整块作试样。每种焦炭需取20个以上的试样作试验,应变速度为1.5X10一、”。室温下焦炭抗压强度大约为12一30MPa,在1 500℃高温下测量时,抗压强度值将增大20%左右。抗压强度的高低与气孔率大小有关。焦炭抗压强度比燕炭杭肚强度大一个数量级,它比焦炭在高炉内实际承受的压应力(约为0.ZMpa)大两个数量级,即焦炭的抗压强度远大于焦炭在高炉内承受的炉料压力,故压应力不是焦炭断裂的主要原因,对评定焦炭强度的意义不大。 (江中纸)
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条