说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 锯切厚度
1)  sawing thickness
锯切厚度
1.
The kinematic point speed compositive theory isadopted to work out a single diamond grit's sawing area and sawing thickness .
引进运动学中的点的速度合成定理求解单颗金刚石磨粒锯切面积和锯切厚度 ,通过详细的理论推导推出了单颗金刚石磨粒锯切速度方程、锯切运动方程和锯切面积和锯切厚度的计算公式。
2)  saw blade thickness
锯片厚度
3)  saw cutting speed
锯切速度
1.
The formulas for calculating equation of saw cutting speed and kinematic equation of saw cutting and cutting area are derived through theoretical derivation in detail.
通过详细的理论推导 ,推出单颗金刚石磨粒锯切速度方程、锯切运动方程和切削面积的计算公式 。
4)  chip thickness
切屑厚度
1.
The mechanism of impacts of cutter runout on the pratical cutting radius,chip form and chip thickness was studied and analyzed.
研究了径向跳动对刀齿的实际切削半径、切屑形状以及切屑厚度的影响机理。
5)  cutting depth
切削厚度
1.
The relationship between sheer stresses and cutting depth is found.
利用位错理论对超声波振动切削过程中剪切应力进行分析 ,从微观方面得出其计算公式 ,发现剪切应力与切削厚度的关
6)  undeformed chip thickness
切削厚度
1.
Influences of the double negative chamfer angles of diamond turning tool and the undeformed chip thickness on the surface rolling effect are analyzed, and the empirical formulas of surface rolling rate are presented.
对汽车轮毂抹平加工的主要工艺参数进行了试验研究 ,分析了金刚石抹平车刀双重负倒棱角度和切削厚度对抹平效果的影响 ,给出了抹平率经验公式。
补充资料:锯切
      用边缘具有许多锯齿的刀具(锯条、圆锯片、锯带)或薄片砂轮等将工件或材料切出狭槽或进行分割的切削加工。锯切可按所用刀具形式分为弓锯切、圆锯切、带锯切(见图)和砂轮锯切等。①弓锯切是将锯条张紧在弓形的锯架上,并作直线往复运动,对工件进行切割,一般在弓锯床(见锯床)上利用动力锯切,也可用手工锯切。由于弓锯切在回程时不进行切削,故效率较低。②圆锯切是在圆锯床上由主轴带动圆锯片旋转对工件进行连续切割,效率较高。③带锯切是在带锯床上利用两个轮子把长而薄的环形锯带张紧,并驱动锯带作连续运动对工件进行切割。宽带锯切的效率高,切口窄,有取代弓锯切的趋势;窄带锯切适于切割扁平工件的外部曲线轮廓或成形的通孔。④砂轮锯切是用高速旋转的薄片砂轮切割工件,适于切割难加工金属材料。各种锯切方法的精度都不高,除窄带锯切外,一般用于在备料车间切断各种棒料、管料等型材。
  

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条