1) residual stress of superficial layer
表层残余压应力
2) surface residual compressive stress
表面残余压应力
3) machining surface residual compressive stress
机加工表面残余压应力
1.
The machining induces two effects on the surface of ceramics: machining cracks andmachining surface residual compressive stress.
本文对热压烧结ZTM／SiCp陶瓷的表面机加工损伤及其对材料强度的影响进行了研究，发现机加工在陶瓷表面引入两类损伤，即机加工裂纹及机加工表面残余压应力。
4) compressive residual stress
残余压应力
1.
The experimental results show that its hardness can be improved up to 25% and the compressive residual stress can reach-200MPa～-250MPa.
实验结果表明,黄铜表面的显微硬度可提高25%左右;材料表面产生的最大残余压应力可高达-200MPa~-250MPa。
2.
,compressive residual stress(CRS),surface roughness(SR) and micro-structure hardening in shot peening(SP) surface on solid particle erosion(SPE) resistance of Ti6Al4V titanium alloy were evaluated.
探讨了喷丸强化(SP)因素(残余压应力引入、表面粗糙度增大和表面加工硬化等)对Ti6Al4V钛合金固体粒子冲蚀(SPE)行为的影响和作用机制,为充分发挥SP改进航空发动机零部件服役性能的潜力提供依据。
3.
,compressive residual stress(CRS),surface roughness(SR) and work-hardening on SPE resistance were investigated.
研究了喷丸强化(SP)对AISI 420马氏体不锈钢抗固体粒子冲蚀(SPE)行为的影响,探讨了喷丸引起的表面残余压应力,表面粗糙度增大和表面加工硬化等三因素对SPE抗力的作用机制。
5) residual compressive stress
残余压应力
1.
Influence of residual compressive stress on warm prestress toughening of HSLA steel;
残余压应力对低合金高强钢热预应力增韧效应的影响
2.
The steel by deep nitriding possessed excellent microhardness gradient and favorable distribution of residual compressive stresses,and the contact fatigue life of nitrided steel under the given load showed a great improvement in relation to carburized 18CrNi4A steel.
深氮化试件具有优良的硬度梯度和残余压应力分布,与渗碳件相比接触疲劳寿命提高3。
3.
The laser shock processing causes the surface layer of metal to plastically deform,and thereby develop a significant residual compressive stress in the surface of metal.
激光冲击处理会使金属材料表层发生塑性变形而产生很高的残余压应力;冲击区的显微组织中会产生高密度位错,有时亦有孪晶与相变产生;金属材料表层的塑性变形、高残余压应力、高密度位错、孪晶以及相变,这些因素的共同作用使得金属材料表面硬度、疲劳寿命获得很大的提高。
6) Surface Residual Stress
表面残余应力
1.
Study on Surface Residual Stress by Turn-milling;
车铣加工表面残余应力的研究
2.
Numerical simulation on surface residual stress for titanium alloy;
钛合金的已加工表面残余应力的数值模拟
3.
A research on the effect of cutting force and surface residual stress of work piece on tooling wear;
刀具磨损与切削力及工件表面残余应力的研究
补充资料：轧辊残余应力(见轧辊应力)
轧辊残余应力(见轧辊应力)
residual stresses in roll
zhagun eanyu yingli轧辊残余应力(residual stresses in roll)见礼辐应力。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条