1) edge shape error
![点击朗读](/dictall/images/read.gif)
刃形误差
1.
Based on the meshing theory,The reason produced by the theoretic edge shape error of slotting tool is dis-cussed in detail in this paper.
以啮合理论为基础,详细分析了插齿刀理论刃形误差产生的原因,提出了插齿刀理论刃形误差修正的方法和计算结果。
2) tolerance of grinding hobber
![点击朗读](/dictall/images/read.gif)
刃磨误差
3) profile error
![点击朗读](/dictall/images/read.gif)
形状误差
1.
Detection of profile error of ship hull plate processing surface;
![点击朗读](/dictall/images/read.gif)
船体外板曲面形状误差评定方法分析
2.
The conventional method of qualitative inspection and description of the profile error is now incapable of meeting the requirement for product quality control in modern society.
针对曲面形状误差评定使用传统的模板定性检测、定性描述的方式已不能满足现代制造对产品质量的控制要求,提出了一种新的参数曲面形状误差计算的迭代逼近法。
4) profile error
![点击朗读](/dictall/images/read.gif)
齿形误差
1.
Research on Coordinate Method for Measuring the Profile Error of Wormgears;
![点击朗读](/dictall/images/read.gif)
坐标法测量蜗轮齿形误差的研究
2.
Measuring the Profile Error of the Involute Gear;
![点击朗读](/dictall/images/read.gif)
齿轮渐开线齿形误差的测量
3.
The tooth profile error and longitudinal form error are calculated,and the change rule with setting angle of them is got.
针对花键的齿形误差和齿向误差,按照误差计算原理,得出了计算结果及其随安装角改变的变化规律。
5) Form error
![点击朗读](/dictall/images/read.gif)
形状误差
1.
Distribution type of form error and its evaluation model;
![点击朗读](/dictall/images/read.gif)
形状误差的分布类型及评定模型
2.
Distribution of direct measurement results of measurement points of form error;
![点击朗读](/dictall/images/read.gif)
形状误差测量中测量点直接测量结果的分布
3.
Reading contributions of generalized displacement sensors in the separation of form error and error motions;
广义位移传感器在形状误差和误差运动分离中的读数贡献
6) form accuracy
![点击朗读](/dictall/images/read.gif)
面形误差
1.
In order to assure form accuracy and surface roughness of optic free-form surface of injection mould core,form grinding of free-form surface was conducted in CNC precision grinder by use of precisely dressed and trued arc-shaped coarse diamond grinding wheel to realize effective mirror grinding.
加工高速钢自由曲面时,面形误差(PV值)可以达到10μm以下,表面粗糙度Ra可以达到约16 nm。
补充资料:J形及L形密封
分子式:
CAS号:
性质:两种均为唇形橡胶密封,截面形状分别为J形和L形。多为纯橡胶制品,也有少数是夹布制品。根据使用条件,一般用天然橡胶或丁腈橡胶制造。结构较简单,摩擦力低,专用于气压或液压机械设备的活塞及活塞杆密封,工作压力在1MPa以下,如用于汽车和火车制动系统及离合器操纵系统中,起传递压力和密封的作用。
CAS号:
性质:两种均为唇形橡胶密封,截面形状分别为J形和L形。多为纯橡胶制品,也有少数是夹布制品。根据使用条件,一般用天然橡胶或丁腈橡胶制造。结构较简单,摩擦力低,专用于气压或液压机械设备的活塞及活塞杆密封,工作压力在1MPa以下,如用于汽车和火车制动系统及离合器操纵系统中,起传递压力和密封的作用。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条