1) eccentricity in stitches
偏心量e
1.
In this paper, the relationship between eccentricity in stitches and structure properties of sewing threads is studied by means of multiple linear stepwise regression and the following result is obtained: eccentricity in stitches is most related to bending rigidity, linear density and friction coefficient of sewing threads.
本文运用相关分析和多元逐步回归分析对缝纫线迹的偏心量e和缝纫线的结构性能之间的关系进行 了研究,发现偏心量e与缝纫线的弯曲刚度、线密度和摩擦系数的关系最密切。
2) Eccentric distance e
偏心距e
3) migration e
偏移量e
1.
It is needed to be tested in the operating process that include the migration e between survey line and centre point of pipe,the height H from centre point in pipe hole to slide ring of triangulation frame and the depth H0 comes from the circular ball in the pipe hole.
现场操作中只需测量测线与管桩中心点的偏移量e,管桩孔口中心到三脚架滑环的高度H以及环型圆球在管桩管内的深度H0,通过这三个参数就可以计算管桩的倾斜角和垂直度。
4) e-value/eccentricity
e值/偏心率
5) State of E polarization
E矢量偏振状态
6) eccentricity
[英][,eksen'trɪsəti] [美]['ɛksɛn'trɪsətɪ]
偏心量
1.
This paper introduces a new rotation way used in turbomachinery, which is eccentricity rotation with the characteristic of assembling conveniently.
介绍了一种应用于叶轮机械的传动方式,即偏心传动,该传动方式具有装配方便的特点;将弹性接触理论应用于该传动方式偏心量的计算,建立了考虑弹性变形时偏心量的计算方法;采用一组实际数据,分析计算方法的适用性,以及弹性变形对偏心量计算的影响。
2.
When design and lamination, There is a eccentricity e of core center axes in advance and it equals to the value of yield degree in rotor center.
在设计及铁心叠片时 ,预先使铁心中心轴线有一个等于转子中心处挠度值的偏心量e。
3.
To ensure the reliability of some industry producing equipments,the rapid calibration and measurement for diameter and installed eccentricity of rotating pieces with different sizes are required.
许多工业制造装备的工作过程中,需实施不同规格回转体直径及安装偏心量的快速校准测量,以保证可靠性。
补充资料：在AutoCAD中偏心圆锥与偏心圆台实体的画法
现在要画一个偏心圆锥,底面在WCS的XY平面上,圆心(0,0,0),半径100,顶点(300,0,400)在ZX平面上.
1)连接PA,PB. A(-100,0,0) B(100,0,0)
图1
在当前坐标下:
2)延长PA到C,使PA=CA;延长PB到D,使PB=DB;
3)连接CD;
4)以CD为直径画圆;
5)用XLINE命令中的二等分选项作角CPD的角平分线PO,交CD于O;
6)过O作CD的垂线,交圆于E,F;
图2
7)用三点UCS命令,取三点为:O,P,C;
8)过点O作PO的垂线GO,交PC于G;
图3
9)再次用三点UCS命令,取三点为O,F,G;
10)现在就可以画椭圆锥了!
cone-e-c-捕捉O点-捕捉F点-捕捉G点-a-捕捉P点;
图4
11)回到WCS,剖切椭圆锥
SL-选择椭圆锥-回车-XY-回车-捕捉P点.
12)删除辅助线条.
图5
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条