1) the extruded sem-finished articles
挤出半成品
2) extruded serni-finished product
挤压半成品
3) extrudant
[eks'tru:dənt]
压出半成品
4) extrusion molding
挤出成型
1.
The research progress in using supercritical CO2 as a plasticizer to reduce the viscosity of polymer melt during extrusion molding and as a foaming agent to make microcellular foams is introduced and the further researches are pointed out.
详述了国内外在超临界二氧化碳降低挤出成型过程中聚合物的熔体粘度和作为发泡剂制备微孔塑料制品两方面的研究进展,指出了目前国内外在超临界二氧化碳(SC-CO2)应用于聚合物挤出成型方面存在的问题。
2.
In the process of PVC low foaming solid sheet extrusion molding,it is critical to control the folw and foaming of the molten polymer.
在PVC低发泡实心板挤出成型中,控制聚合物熔体的流动和发泡是保证产品质量的关键,重点介绍了生产工艺和原理,并分析了生产中的技术要点,提出了解决的办法。
3.
The self-made new type of hydraulic vibration extrusion equipment was adopted to study the rheological behavior of high density polyethylene(HDPE) under vibration extrusion molding.
利用自行研制的新型液压振动挤出装置研究了高密度聚乙烯(HDPE)在振动场中挤出成型时的流变行为。
5) extrusion molding
挤出成形
1.
The blending technology and the improvement of the mixed silicone rubber for extrusion molding with 2, 4-dichlorobenzoyl peroxide, including the low hardness mixed silicone rubber, the mixed silicone rubber with no connection with cored wires, high electric strength mixed silicone rubber.
介绍了用2,4-二氯过氧化苯甲酰作硫化剂的挤出成形用混炼硅橡胶(包括低硬度混炼硅橡胶、不粘连芯线的混炼硅橡胶、高电气强度电线用混炼硅橡胶)的配制方法及改进其加工和表面性能的方法;同时,还介绍了用甲基苯甲酰类过氧化物作硫化剂时改进混炼硅橡胶表面性能的方法(包括添加含氢硅油、硅藻土、二烷基过氧化物或过氧化苯甲酰以及细化硫化剂粒子)。
2.
The blending technomogy of the mixed silicone rubber for extrusion molding with other organic peroxide as curing agent was introduced.
介绍了用二叔丁基过氧化己甲酰作硫化剂的挤出成形混炼硅橡胶的配制方法、通过添加水分捕捉剂及抑制剂、特定结构的聚醚改性硅油、特定结构的有机过氧化物改善加成型挤出成形混炼硅橡胶的贮存稳定性、减少制品内部气泡的方法,以及通过添加硫化剂分解产物的清除剂、含氢硅油或采用复合硫化剂的不需二次硫化的混炼硅橡胶的配制。
6) extrusion moulding
挤出成型
1.
It introduced the extrusion moulding technology of pvc surface-crusting low-foamed wided door sheet.
介绍了PVC结皮低发泡宽幅门板的挤出成型技术。
2.
This article is about the new development in extrusion moulding field, and introduces the new extrusion moulding technique and equipment at K2001.
综述了挤出成型技术领域近年来一些新的发展趋势。
3.
This paper introduces the production technology of the injection and extrusion moulding of Nylon 11.
介绍尼龙11的注射成型和挤出成型工艺,并讨论了生产中易出现的问题及其解决办法。
补充资料：成品检验(见成品验证)
成品检验(见成品验证)
finished product inspection: see finished product verification
山e叩Pinjian四n成品检脸(finishedp耐uct inspection)见成品脸证。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条