1) Deswelling/swelling behavior
溶胀或消溶胀行为
2) deswelling behavior
消溶胀行为
1.
The morphology, temperature responsive behaviors and deswelling behaviors of the hydrogel were investigated.
以无机黏土作为交联剂制备了新型聚(N-异丙基丙烯酰胺)/黏土纳米复合水凝胶(PNIPA/Clay),对其结构、温度敏感性和消溶胀行为等进行了研究。
3) swelling behavior
溶胀行为
1.
Taking conductivity and weight measurements as two methods,the influences of temperature and pH on swelling behavior for polyacrylamide/calcium lignosulfonate composite gel(PAAm-Ca2+-LGS gel) were studied.
采用电导和称重两种方法研究了聚丙烯酰胺/木质素磺酸钙凝胶的溶胀行为及温度和pH的影响。
2.
Copolymer hydrogel was synthesized from acrylamide(AM) and hydroxyl ethylmethacrylate(HEMA),and the swelling behavior of the hydrogel film was studied.
对丙烯酰胺(AM)与甲基丙烯酸β-羟乙酯(HEMA)进行共聚制备的水凝胶角膜接触镜膜的溶胀行为进行了详细研究,结果表明,水凝胶膜对pH敏感。
3.
Several factors influencing the viscosity of coal slurries were discussed,which include solvent properties,coal concentrations,moisture content,macerals of coal,shear rate,temperature,swelling behavior,etc.
研究结果表明,低温下影响煤浆黏度变化的主要因素是溶剂本身的性质,煤浆的表观黏度随温度升高而降低;随温度继续升高在较宽温度范围内黏度变化不大,这是由溶剂性质以及煤在溶剂中的溶胀行为共同作用的结果;当温度达到约220℃后继续升高温度溶胀作用逐渐占优势,从而导致煤浆体系的表观黏度逐渐增大。
4) swelling/deswelling rate
溶胀/消溶胀速率
5) swell
[英][swel] [美][swɛl]
溶胀
1.
Swell of the Emulsion and Effect Factor in Emulsion Liquid Membrane Separation;
乳状液膜分离中的乳液溶胀及影响因素
2.
Release in vitro and swelling of 5-Fu-loaded chitosan microspheres for intranasal administration;
鼻用氟脲嘧啶壳聚糖微球的体外释放及溶胀影响因素
3.
The dominant factors of deep profile control and displacement are particle size and swelling ability of crosslinked polymer micro-ball.
交联聚合物微球的颗粒粒径和溶胀性能是影响调驱效果的主要因素。
6) swelling
[英]['swelɪŋ] [美]['swɛlɪŋ]
溶胀
1.
Principium study on swelling characteristic of Yilan coal;
依兰煤溶胀特性的初步研究
2.
Study on Shengli coal swelling in different solvents;
不同溶剂对胜利煤的溶胀研究
3.
Effects of surfactants on the extraction of penicillin and the swelling of emulsion liquid membranes;
液膜常用表面活性剂对青霉素提取率及液膜溶胀的研究
补充资料：锻压:胀形
在管坯内部或在板坯一侧通以高压液体﹑气体或放入刚体瓣模﹐迫使管﹑板塑性变形﹐以製成工件的衝压成形工艺。由於受到材料塑性和塑性变形能力的限制﹐胀形程度不宜过大。胀形可用以製造平板的局部突起﹑凹坑﹑花纹﹐波纹管﹐皮带轮和自行车五通接头等。图 皮带轮液压胀形工序
为皮带轮液压胀形工序。胀形时﹐作为介质的气体﹑液体的压力随工件材料﹑厚度﹑变形情况而异﹐一般用10～13兆帕﹐也有用高能率成形和超塑成形的。胀形变形均匀﹐只需要一块模具(通常为凹模)﹐可以节省製模费用﹐但辅助工序较多﹐效率不高。
为皮带轮液压胀形工序。胀形时﹐作为介质的气体﹑液体的压力随工件材料﹑厚度﹑变形情况而异﹐一般用10～13兆帕﹐也有用高能率成形和超塑成形的。胀形变形均匀﹐只需要一块模具(通常为凹模)﹐可以节省製模费用﹐但辅助工序较多﹐效率不高。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条