1)  the unbalancing injection system
非平衡浇注系统
2)  non-equilibrium
非平衡
1.
The double fluid model of the non-equilibrium ionization zone in the detonation plasma;
爆轰等离子体非平衡区的双流体模型
2.
Heat and mass transfer character on adsorption bed with consideration of non-equilibrium adsorption;
非平衡吸附特征的吸附床传热传质特性
3.
Numerical simulation of fixed-bed adsorption by non-isothermal non-adiabatic and non-equilibrium model;
气体变压吸附非等温非绝热非平衡模型计算
3)  Non-stationary
非平稳
1.
Application of Multidimensional Non-stationary Time Series on Fault Diagnosis of Spindle;
多维非平稳时间序列在机床主轴故障诊断中的应用
2.
Simulation of non-stationary spatial correlative time histories of multi-point ground motion;
非平稳空间相关多点地震动合成方法研究
3.
New method to improve identification ability of neural networks in non-stationary environment;
非平稳环境下提高神经网络辨识能力的新方法
4)  Unbalance
非平衡
1.
Application of the CrAlTiN Coating of Closed Field Unbalanced Magnetron Sputter Ion Plating on the PCB Micro-drill;
闭合场非平衡磁控溅射离子CrAlTiN镀层在PCB用微钻中的应用
2.
Comparison analysis of a matrix converter under balanced and unbalanced input voltages;
矩阵变换器平衡/非平衡输入的对比分析
3.
Study on Definitions and Measurments of Power in Electric Power System under Nonsinusoidal and Unbalanced Operation;
电力系统非正弦和非平衡运行状态功率定义与测量的研究
5)  non-equilibrium stage
非平衡级
1.
In this paper,a non-equilibrium stage method,t he differential unit method,which is suitable for the multi-stage separation tec hnology of hydrate, is proposed to aim at separating hydrogen from H 2+CH 4 ga s mixtures and using tetrahydrofuran as the promoter.
针对H2+CH4 体系在四氢呋喃 (THF) 水溶液中H2 的分离, 提出了适合水合物多级分离技术的非平衡级算法———微元法, 对此方法做了详尽的阐述。
6)  nonequilibrium
非平衡态
1.
The paper discusses the fundamentals of laser generation from the angle of nonequi- librium thermodynamics and also explains that the so- called negative temperature means the decrease of entropy in nonequilibrium, so that system tends to be ordery.
从非平衡态热力学角度讨论了激光产生的基本原理,其中还解释了所谓负温度意味着非平衡态熵减少,系统趋向有序。
2.
Lax-Friedrichs Scheme Based on Nonequilibrium for Multifluid Flows;
针对当前多介质流体计算中出现的速度和压强在介质界面处产生伪振荡的问题,我们设计了一种基于非平衡态的Lax-Friedrichs格式。
参考词条
补充资料:浇注系统
      为将液态金属引入铸型型腔而在铸型内开设的通道。浇注系统(见图)包括:①浇口杯。承接浇包倒进来的金属液,也称外浇口。②直浇口。联接外浇口和横浇口,将金属液由铸型外面引入铸型内部。③横浇口。联接直浇口,分配由直浇口来的金属液流。④内浇口。联接横浇口,向铸型型腔灌输金属液。
  
  浇注系统的作用是:控制金属液充填铸型的速度及充满铸型所需的时间;使金属液平稳地进入铸型,避免紊流和对铸型的冲涮;阻止熔渣和其他夹杂物进入型腔;浇注时不卷入气体,并尽可能使铸件冷却时符合顺序凝固的原则。内浇口的总截面积、横浇口的总截面积和直浇口的总截面积是浇注系统的重要参数。根据内浇口、横浇口、直浇口的各自总截面积的比例不同,浇注系统分为开放式和封闭式两种。这里所说的截面积都是指与液流方向垂直的最小截面面积。当内浇口的总截面积最小时,浇注开始后整个浇注系统很快就充满了金属液,有利于阻止熔渣及夹杂物进入型腔,这种浇注系统通常称为封闭式浇注系统,一般都优先采用。当横浇口或直浇口的总截面积小于内浇口的总截面积时,浇注过程中金属液不会完全充满浇注系统,这种浇注系统通常称为开放式浇注系统,仅在特殊工艺采用。
  
  浇口杯的作用是将浇包倾注的液态金属导入直浇口。小型铸件的浇口杯大都为漏斗形,上口的直径应是直浇口的 2倍以上,而且一般都在造型时直接在铸型上做出。中型以上的铸件,浇口杯常为盆形,一般都单独做出后置于铸型上面。质量要求高的铸件还要在浇口杯中设置特殊的集渣装置。
  

说明:补充资料仅用于学习参考,请勿用于其它任何用途。