1) Cold forging punch pin of bearing roller
轴承滚子冷镦冲头
2) cold forge dies
冷镦冲头
1.
The automobile differential shell bolt cold forge dies,which can only produce2,000bolts at their maximum,have a short and unstable life.
汽车差速器壳螺栓冷镦冲头使用寿命低 (仅生产 10 0 0~ 2 0 0 0只产品 ) ,且寿命长短不一 。
3) roller bearing
滚子轴承
1.
Development of inner ring rib grinding machine of tapered roller bearing;
圆锥滚子轴承内圈挡边磨床研制
2.
Effect of double row cylindrical roller bearing installment on bearing failure;
双列圆柱滚子轴承安装对轴承失效的影响
3.
Rigidity computation of roller bearing under radial force
径向力作用下滚子轴承的刚度计算
4) bearing roller
轴承滚子
1.
A study on audio frequency characteristic of a bearing roller in nondestructive testing;
轴承滚子无损检测中音频特性的研究
2.
Data acquisition and processing of nondestructive testing for bearing roller;
轴承滚子无损检测的信号采集与处理研究
3.
Heat treatment of G20CrNi2MoA steel for bearing roller in stead of G20Cr2Ni4A steel
G20CrNi2MoA钢代替G20Cr2Ni4A钢制造轴承滚子的热处理试验
5) roller bearings
滚子轴承
1.
Unsymmetric shape modification of cylindrical roller bearings;
圆柱滚子轴承的非对称修形
6) full-roller bearing
满滚子轴承
补充资料:自动冷镦机、多工位螺栓自动冷镦机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
(一)加工精度 | 参照GB9166-88、JB/T3053-91 | ||||||
1、冲头夹持器模孔中心线对夹持器后支承面的垂直度(mm) 在100长度上 | 0.008 | 0.01 | 0.015 | >0.015 | |||
2、凹模座模孔中心线对凹模后座支承面的垂直度(mm) 在100长度上 | 0.008 | 0.01 | 0.015 | >0.015 | |||
3、冲头夹持器模孔中心线对滑块行程的平行度(mm) 在100行程上 | 0.016 | 0.02 | 0.02 | >0.02 | |||
4、滑块行程对机身上与凹模座贴合的垂直面的垂直度(mm) 在100行程上 | 0.016 | 0.02 | 0.02 | >0.02 | |||
5、工件头部对工件杆部中心线的偏移量(mm) | <0.20 | 0.20~0.25 | 0.25~0.30 | >0.30 | |||
(二)生产率(件/分) | |||||||
20mm | >80 | 70 | 65 | <65 | |||
30mm | >60 | 50 | 45 | <45 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条