1) algebraic stress model
代数应力模型
1.
WT5”BZ]This paper introduces an algebraic stress model with k and was ε equation based on the Renormalization Group theory.
将湍流重整化群 ε方程与 Zhang Jian提出的新代数应力模型结合 ,用于模拟煤粉浓淡燃烧器喷口强旋转流场。
2.
By analyzing the components of Reynolds stresses of implicit algebraic stress model(IASM) in the paper, that Reynolds stresses in buoyant turbulent flows were produced by both strain and buoyancy is considered.
通过对隐式代数应力模型应力结构的分析，认为湍浮力流动的应力由应变和浮力作用引起，从而利用应力输运的线性近似和平衡近似提出了非线性各向异性湍浮力模型· 该模型避免了数值奇异，其可靠性通过计算和实验的对比得到了验证
2) ASM
代数应力模型
1.
An ASM turbulence model is developed.
分析了深筒式消力井内的水流因受固体边界的约束,水流有各向异性的特点,论述了运用数值模拟的方法研究该问题的重要意义,并建立了二维紊流代数应力模型。
2.
An ASM turbulence model is developed ,and the boundary conditions are established.
本文首次运用数值模拟的方法对圆形深筒式消力井内的水流流场进行了研究,建立了的二维紊流代数应力模型,确立了相应的边界条件,说明消力井的消能过程实际上是时均能转化成紊动能,继而由于流体粘性而消耗为热能的过程。
3.
A new data simulation method of the Algebraic Stress Method(ASM) for the flow path of hydraulic valves was put forward from the Naiver-Stokes equations.
本文根据Ｎａｉｖｅｒ－Ｓｔｏｋｅｓ方程推导一种比传统数学方法更优越的代数应力模型。
3) algebraic stress models
代数应力模型
1.
Nonlinear eddy viscosity and algebraic stress models are currently providing an invaluable link between the more common linear eddy viscosity turbulence models and the full differential Reynolds stress forms.
非线性涡黏性系数模型和代数应力模型联系了线性涡黏性系数湍流模型和完整的微分雷诺应力模型。
4) stress-algebraic model
应力代数模型
1.
Based on stress-algebraic model,anisotropic turbulent buoyant jet with variable density is studied.
在应力代数模型基础上引入密度状态方程建立了变密度的各向异性湍浮力射流模型,并给出了浮力系数的简单计算式。
5) algebraic-stress turbulent model
代数应力湍流模型
1.
The anisotropic algebraic-stress turbulent model is introduced to simulate the turbulence items, and algebraic-stress turbulent model of planar 2-D pollutant convection-diffusion in curvilinear coordinates is built.
对浅水流动的控制方程和深度平均的污染物扩散输移的控制方程进行坐标变换,湍流的模拟采用各向异性代数应力湍流模式,建立了曲线坐标下平面二维水流计算和污染物扩散输移的代数应力湍流模型。
2.
The algebraic-stress turbulent model is introduced to establish an algebraic-stress turbulent model for 2-D plane flow in curvilinear coordinates.
本文对浅水流动的控制方程进行坐标变换,导出了非正交曲线坐标下平面二维水流计算的代数应力模型公式,建立了非正交曲线坐标下平面二维水流计算的代数应力湍流模型。
6) algebraic stress-flux model
应力通量代数模型
补充资料：轧辊残余应力(见轧辊应力)
轧辊残余应力(见轧辊应力)
residual stresses in roll
zhagun eanyu yingli轧辊残余应力(residual stresses in roll)见礼辐应力。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条