说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 滑行刨煤机
1)  gleithobel plough
滑行刨煤机
1.
Manufacture and application of high-power fast gleithobel plough;
大功率快速滑行刨煤机的研制与应用
2)  toe in plough
滑行的刨煤机
3)  slide plough
滑动刨煤机
4)  self propelled plough
自行刨煤机
5)  plow [英][plau]  [美][plaʊ]
刨煤机
1.
Simulation & study of three directional loads of plow bit on plow;
刨煤机刨刀三向载荷的模拟分析
2.
Has carried on the study about compatibility of the longwall face equipment for fully automatic plow mining face in thin seam,analyzed the different types PRT,designed a new type face end support according to the different compatibility equipments.
对薄煤层全自动化配刨煤机工作面的配套设备进行了探讨,对不同的机头配套形式进行了分析,并依据配套设计不同的端头支架。
3.
Based on an example from Datong Coalmines Group,the paper analyses possibility and usage of heavy plow under the conditions of thin seam coal face with Two Hard Roofs and gives out some proposals.
通过大同煤矿集团公司采用全自动刨煤机系统开采薄煤层的实例,分析了在“两硬”薄煤层地质条件下进行刨煤机开采的可行性和作用,并针对性地提出了建议。
6)  Slicer [英]['slaisə]  [美]['slaɪsɚ]
刨煤机
1.
Mining Application of DBT Full Automation Slicer Technology in the Low Coal Seam of Xishan;
DBT全自动化刨煤机技术在西山薄煤层开采应用
2.
Research on Auxiliary Relative Equipment and Safely Mining Technology of Slicer Coal Face;
刨煤机工作面辅助设备配套与安全开采技术研究
3.
This paper describes the main capability and structure of a new type slicer,and denmenstrating the capability of inceasing the block rate,coal quality and output in working face.
介绍了新型刨煤机的主要性能和结构特点以及使用条件,结合晋城矿区煤层赋存条件,论证了刨煤机在晋城矿区使用能大幅度地提高综采工作面煤炭块率。
补充资料:机床: 直齿锥齿轮刨齿机
      用成对刨齿刀按展成法(见齿轮加工)粗﹑精加工直齿锥齿轮或斜齿锥齿轮齿部的齿轮加工机床。直齿锥齿轮刨齿机可加工直径小至5毫米﹑模数为0.5毫米﹐大到直径为900毫米﹑模数为 20毫米的工件。加工精度一般为7级(JB180-60)﹐适用于中小批量生产。直径大于900 毫米的直齿锥齿轮则在按靠模法加工的刨齿机上加工﹐最大加工直径可达5000毫米。直齿锥齿轮刨齿机(见图 直齿锥齿轮刨齿机的组成)的上﹑下刀架作直线往复的切削运动﹐整个刀架装在摇台上﹐并随摇台作一定角度的摆动﹐与工件的相应角度的正反回转运动一起构成展成运动。摇台每上下往复摆动一次﹐就完成一个齿的切削运动。这时工件随床鞍退出﹐转过一定角度进行分齿。然后床鞍又进到工作位置﹐开始切削第二个齿。床鞍的进退由进给鼓轮控制。全部齿切削完毕后机床自动停止。工件主轴箱按工件的根锥角在床鞍上调整位置。一般直齿锥齿轮刨齿机的工件主轴与摇台等高﹐不能调整﹐只能加工直齿。有的刨齿机的工件主轴的高度可调整﹐并带有切向刀架﹐可用以刨削斜齿锥齿轮。能刨削鼓形齿的刨齿机的刀架滑板有两条可调导轨﹐使刀架的运动轨迹略呈曲线﹐以刨出鼓形。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条