1) Fe_3Al-based coating
Fe3Al基涂层
2) Fe3Al-based alloy
Fe3Al基合金
1.
Current research status of welding of Fe3Al-based alloys;
Fe3Al基合金焊接问题的研究现状
3) Fe 3Al
Fe3Al
1.
The mechanical properties of Fe 3Al based alloy were investigated from ambient temperature to elevated temperature.
研究了 Fe3Al合金从室温到高温力学性能的变化情况 ,发现在 10 0～ 30 0℃之间 ,该合金的抗拉强度出现了反常温度现象 ,即随着温度的升高 ,抗拉强度也提高 ,并在 30 0℃附近达到最大值。
2.
Fe 3Al-based alloys containing VC and TiC particles are fabricated by melting and casting process.
以Fe3Al金属间化合物作为基体 ,采用反应铸造法制备了含VC ,TiC颗粒Fe3Al基合金并研究了颗粒相在Fe3Al合金中的形成机理及颗粒相的加入对Fe3Al基合金显微组织结构的影响 。
3.
Fe 3Al based alloys containing 1.
采用反应铸造法制备了含VC、TiC颗粒的Fe3Al基合金 ,并研究了颗粒相的加入对Fe3Al合金组织结构和力学性能的影响。
4) Fe_3Al
Fe3Al
1.
Fe_3Al powder with different Al content was prepared by mechanical alloying technique and annealing treatment.
采用机械合金化结合退火处理工艺制备了不同Al含量的Fe3Al粉体,并经真空热压烧结得到Fe3Al金属间化合物块体材料,对其烧结后的微观结构、力学性能以及Al含量的影响进行了试验研究。
2.
The layers of Fe_3Al Intermetallic are prepared on the substrate of steel by single track laser cladding with powders of Fe_3Al.
以纯Fe3Al粉末为原料 ,采用同步送粉式激光熔覆工艺在低碳钢基体表面合成Fe3Al金属间化合物。
3.
A new kind of Fe_3Al intermetallic base friction material was prepared by hot pressing.
采用热压烧结方法制备了一种适用于重载高速工况下的新型 Fe3Al金属间化合物基摩擦材料 ,并对其微观结构、力学性能以及干滑动摩擦磨损性能进行了试验研究。
5) Ni-based coating
镍基涂层
1.
Influence of spray-welding technology on microstructures and properties of Ni-based coating on titanium substrate;
喷焊工艺对钛基体镍基涂层显微组织和性能的影响
2.
The residual stresses of the coatings with different composition and thickness Ni-based coatings sprayed by HVAF on the copper substrate were measured by X-ray diffraction (XRD) and curvature methods.
采用X射线应力分析技术和曲率法测试了在铜基体上喷制不同成分、厚度的镍基涂层以及改变基体厚度喷制的涂层的残余应力。
3.
This article has mainly studied the effect mechanism of certain Ni-based coating on thermal fatigue damage resistance of wheel cast steel,and experiments were performed on both the samples with or without coating under cycling temperature amplitude of 450～20 ℃.
研究发现,镍基涂层试样在涂层表面出现一些腐蚀坑和微裂纹,但具有层状结构的韧性镍基涂层未出现剥落现象,涂层层状结构阻碍了涂层裂纹向基体的传播,镍基涂层很好地避免了基体材料的热疲劳损伤。
6) nickel-based coating
镍基涂层
1.
Wear properties of nickel-based coating sprayed by different thermal spraying technologies;
不同热喷涂技术制备镍基涂层的摩擦磨损性能
补充资料：Au-Pd-Cr-Pt-Fe-Al-Y alloys
分子式：
CAS号：
性质：金基与钯、铬、铂、铁、铝和钇的多元合金，电阻系数最高。生产方法参见金钯铬合金。可用作高温应变材料。
CAS号：
性质：金基与钯、铬、铂、铁、铝和钇的多元合金，电阻系数最高。生产方法参见金钯铬合金。可用作高温应变材料。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条