说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 包芯纱机
1)  Corn spun Spinning Frame
包芯纱机
2)  core spinning frame
包芯纺纱机
3)  Core-spun Yarn
包芯纱
1.
Key Production Technology of Weft Elastic Fabric with Spandex Core-spun Yarn;
氨纶包芯纱纬弹织物的生产技术要点
2.
Research and development on new core-spun yarn by wrap spinning;
新型包绕纺包芯纱的开发与研究
3.
Production of Milk Protein Fiber Polyurethane Core-spun Yarn;
牛奶蛋白纤维氨纶包芯纱的生产
4)  core spun yarn
包芯纱
1.
Production Practice of Cotton Polyester Short Fiber Core spun Yarn;
棉涤短纤包芯纱的生产实践
2.
Study on spinning parameter of wool/spandex core spun yarn on woolen spinning system;
毛粗纺氨纶包芯纱纺纱工艺的研究
3.
The Behavior Analysis About Percentage Component of Blended Fiber Core Spun Yarn;
包芯纱中氨纶含量测试方法的改进
5)  core yarn
包芯纱
1.
The development of polyester cotton core yarn on disc swirl spinning frame;
圆盘式旋流纺涤棉包芯纱的研究
2.
The core yarn spun Modal from Lenzing AG, Lenzing/Austria is made with a bare elastane yarn inside.
本文介绍的包芯纱添纱产品的莫代尔纱由Lenzing公司提供,弹性裸丝由Lenzing澳洲公司提供,这种包芯纱能使织物具有永久弹性。
3.
This paper studies the spinning of core yarns in channel spinning machine without any additional machine parts.
本文研究了在管道纺纱机上不添加构件而进行包芯纱的纺制。
6)  core spinning
包芯纺纱
1.
Development and existing problems in core spinning;
包芯纺纱技术的发展及存在问题
补充资料:Z8612热芯盒射芯机操作规程
1、遵守铸造设备通用操作规程。
2、工作前还必须遵守:
a、
检查设备上行程开关和碰块的位置是否正确,如不正确,必须调整。
b、
接通电源,打开压缩空气伐门,先用手动方法,对各机构逐进行点动试车,然后用自动方法,进行一个循环试车,确认一切正常后,方可进行生产。
3、工作中还必须遵守:
a、
在设备开动后,一个循环未完成时,不许中途调整电器,以免发生误动作,造成设备人身事故;
b、
设备的每一个循环后,必须用喷咀清除芯盒上残存的砂子,并喷涂分型剂;
c、
在未切断电源和所气源前,不准将手伸入芯盒和夹紧器之间的空隙处,或把手放在导轨上,以免发生人身事故。
d、 一般不准空射,如必须空射,一定要把压缩空气伐门关小;
e、 如果用手操作,不准同时操作两个电器开关。
4、工作后还必须遵守:
a、
操纵各个电器开关,使设备各机构恢复到原始位置,然后切断电源和气源;
b、 折下射砂头,清理积砂和粘砂;
c、 清除排气塞内的粘砂;
d、
取下射砂筒,清除缝隙中的粘砂,最后用石蜡涂擦内壁,但不要将缝隙堵塞;
e、 清除闸板上的积砂,并在闸板上涂石墨粉,以减少磨擦;
f、 清除导轨和导杆上的积灰和积砂,并涂上一层润滑油。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条