说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 站用变压器
1)  station transformer
站用变压器
1.
The reason of unbalanced load voltage for station transformer in 220 kV substation was analyzed,the important influence of null line wirings in three-phase four-wire system on three-phase load voltage balancing was explained,and put forward a kind of simple,visual and practical vector analysis method.
分析一220kV变电站站用变压器负荷电压不平衡的原因,说明了三相四线制中的零线接线准确与否对负荷三相电压平衡性的重要影响,并提出了一种简单、直观的实用矢量图分析方法。
2)  500 kV auxiliary transformer
500kV站用变压器
3)  single operator transformer
单站焊接变压器
4)  multioperator welding transformator
多站焊接变压器
5)  hydropower station transformer
水电站变压器
1.
Following the change of time and technical measures,some hidden troubles in the hydropower station transformer,such as the malpractices and its harmful aftermath in the main connection mode and the transformer operation,and the overtension of the terminal voltage and the auxiliary power,were emerged,it is necessary to reform aiming at deferent status.
随着时间和技术措施的变化,水电站变压器存在的相关隐患也渐渐浮出水面,比如水电站主接线方式和变压器运行过程中存在的弊端及造成的不利后果,水电站发电机机端电压及厂用电电压过高等,需要针对不同的情况进行改造。
6)  transformer house
变电站;变电室;变压器室
补充资料:厂用工作变压器


厂用工作变压器
unit auxiliary transformer

ehongyong gongzuo branyaq-厂用工作变压册(unit auxiliary transformer) 向机组中压厂用负荷供电的变压器;也称为单元厂用变压器。发电机变压器组接线的机组的厂用工作变压器均从发电机至主变压器的引线上支接。 厂用工作变压器具有如下特点: (l)厂用工作变压器的接线组别应满足与厂用起动/备用变压器的并联切换,并考虑厂用中压系统的中性点接地方式。 (2)厂用工作变压器的阻抗决定于具体工程的厂用中压设备的允许短路电流承受能力和单台最大电动机正常起动和电动机成组自起动时厂用母线的允许电压水平,也可采用分裂绕组变压器以减少厂用母线的短路电流。 (3)厂用工作变压器一般不采用有载调压。对于有进相运行要求的大容量发电机,或发电机出口设断路器利用厂用工作变压器起动机组使厂用母线电压波动超过允许范围时,可采用有载调压变压器。 (4)厂用工作变压器应能承受当高压侧系统阻抗为零其低压侧出口处三相金属性短路,变压器所有绕组(包括稳定绕组)不应变形和损坏,并能继续运行。对于直接与发电机联接的厂用工作变压器,还要考虑发电机灭磁时间对其承受短路能力的影响。 (5)厂用工作变压器为户外油浸式变压器,由于负荷率高,额定容量时一般采用55℃温升,冷却方式采用ONAN/ONAF,以使变压器有较好的运行条件和较长的寿命(30~40年)。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条