1) Total tray pressure difference
总板压降
2) total pressure drop
总压降
1.
Impact to the cyclone separator total pressure drop and the separation efficiency which is caused by the airspeed and the liquid-gas ratio is investigated on the cold mould experimental apparatus in the laboratory,and provided plenty of basis for the industrial application of the cyclone separator.
在实验室冷模实验装置上考察了空速和液气比对旋流板分离器总压降和分离效率的影响,为旋流板分离器的工业应用提供了依据。
3) pressure drop
塔板压降
1.
The critical gas velocity through valve holes,pressure drop,entrainment and weeping were measured.
采用空气-水系统,在500 mm×500 mm的方形塔内,对不同浮阀的升程对导向梯形浮阀塔板的流体力学进行了实验研究,测定了塔板压降、泄漏和雾沫夹带。
2.
The critical gas veocity through、valve holes,pressure drop,entrainment and weeping have been measured.
应用空气－水系统，在１６００ｍｍ×４００ｍｍ的矩形塔内，对梯形导向浮阀塔板的流体力学进行了实验研究，测定了阀孔临界气速、塔板压降、雾沫夹带和泄漏。
3.
The correlations have been obtained for the critical gas velocity through valve hole,pressure drop,entrainment and valve hole gas velocity at weeping point, which can be used in the design of trapezoidal directed valve trays.
本文探讨了该塔板的流体力学模型，得出梯形导向浮阀塔板的阀孔临界气速、塔板压降、雾沫夹带和泄漏点孔速的关联式，可供梯形导向浮阀塔板设计之用。
4) tray pressure drop
塔板压降
1.
Research of entrainment and tray pressure drop of new directed bridge valve trays;
新型导向桥阀塔板的雾沫夹带和塔板压降
5) tray pressure drop
板压降
1.
In the experiments, hydraulic properties, such as tray pressure drop, entrainment rate and leakage rate, were measured, and mass transfer efficiency were determined through the m.
在1000mm×350mm规格的矩形实验塔中,应用典型的水-空气冷模实验系统对3D圆阀和F1型浮阀两种塔盘进行了对比实验研究,测定了多种气液负荷下两种圆形浮阀塔板的板压降、雾沫夹带和漏液量等流体力学性能。
2.
The hydraulic properties,such as tray pressure drop,entrainment rate,and weeping rate were measured,and the mass transfer efficiency was determined through the method of oxygen-absorptions.
应用典型的水-空气冷模实验系统对3D条阀、STV条阀和F1型浮阀3种条阀进行了对比实验研究,测定了多种气液负荷下3种浮阀塔板的板压降、雾沫夹带和漏液量等流体力学性能,利用氧解吸法测定了3种浮阀塔板的传质效率。
6) plate pressure drop
塔板压降
1.
The hydrodynamic performance index-plate pressure drop, etc, was investigated by using air-water system in a column with side length of 500×500mm.
开发出一种新型微孔介质塔板—泡沫镍塔板 ,并在一个 5 0 0× 5 0 0mm2 有机玻璃方塔内用空气—水系统测定了其流体力学性能指标—塔板压降等 ,用二氧化碳解吸实验测定了塔板效率 ,研究了它们随空塔动能因子、堰高和液流强度变化的规律。
2.
The hydrodynamic performance index-plate pressure drop, weeping, etc, was investigated by using air - water system in a column with side length of 500mm X 500mm, and the changing rules of plate pressure - drop, weeping with weir height, liquid strength or F factor were obtained.
开发出几种新型塔板多孔分离罩形元件——丝网翠、小孔罩和铜砂微孔罩,并将其设计成不同的形状, 在一个500 mm×500 mm有机玻璃方塔内用空气-水系统测定了其流体力学性能指标——塔板压降、漏液等, 研究了它们随板孔动能因子、堰高和液流强度变化的规律。
补充资料：板带轧制压下规程(见板带轧制规程设计)
板带轧制压下规程(见板带轧制规程设计)
draughting schedule for plate and strip rolling
bandai zhazhi yaxia guieheng板带轧制压T规程(draughting，ehedule forplate and strip rolling)见板带札制规程设计。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条