说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 高碱度烧结
1)  high-basicity sintering
高碱度烧结
2)  high basicity sinter
高碱度烧结矿
1.
Mineralogical composition and microstructure of high basicity sinters of Laisteel,Baosteel,Ansteel,and Jiusteel were investigated by X-ray diffraction,optical microscopy and scanning electron microscopy.
采用X射线衍射、光学显微镜和扫描电镜对莱钢、宝钢、鞍钢和酒钢烧结矿进行了研究,提出了高碱度烧结矿(w(CaO)/w(SiO2)=1。
2.
20,aimed at the determination of most appropriate sintering parameters for the production of high basicity sinter.
20倍高碱度烧结矿的烧结工艺参数进行试验研究,以寻求与高碱度烧结矿生产相适应的烧结工艺参数。
3.
On the basis of analyzing the material conditions and the sinter quality (R=1 65~1 95) of №2 sintering plant in Hangang during January to August in 2000,the view of production of high basicity sinter(1 8~1 9) could be helpful to increasing sinter output and improving sinter quility was propose
通过对 2 0 0 0年 1~ 8月邯钢二烧的烧结原料和生产的碱度为 1 6 5~ 1 95的烧结矿进行分析 ,认为在此原料条件下生产碱度为 1 8~ 1 9的高碱度烧结矿是可行的 ,其碱度波动可控制在± 0 0 5范围内 ,这样不仅可提高烧结矿的结块率 ,改善其粒度组成和强度 ,同时还可增产降耗。
3)  high basicity agglomerated flux
高碱度烧结焊剂
1.
On the basic of the reference,aimed at high basicity agglomerated flux,the relation of the parameters including the current,voltage and welding speed,the position of the twin-wire and its space,the heat input and the form of groove was systemically analyzed by the overlaying o.
在参考相关文献的基础上,针对高强钢用高碱度烧结焊剂,通过在平板表面堆焊和V型坡口对接板试验,系统分析了焊接电流、电弧电压、焊接速度、双丝位置组合及间距、线能量、坡口形式等与焊道成形的关系。
4)  ultrahigh-basic sinter
超高碱度烧结矿
1.
In this paper,the production statue of ultrahigh-basic sinter in Hang Zhou I&S Co.
介绍了杭钢生产超高碱度烧结矿的情况,总结分析了超高碱度烧结矿的生产特点,以及成品矿的物理性能和冶金性能。
5)  double basicity sintering
双碱度烧结
6)  sinter basicity
烧结矿碱度
补充资料:高碱度烧结矿


高碱度烧结矿
high basicity sinter

gaojiandu shaojiekuang高碱度烧结矿(high basieity sinter)碱度(Cao/SiO:)为1.6以上的烧结矿。碱度超过2.5时,则称超高碱度烧结矿。它的含铁矿物为磁铁矿、赤铁矿,私结相矿物主要是铁酸一钙、铁酸二钙,以及少量硅酸二钙和硅酸三钙。高碱度烧结矿机械强度高、粉末少、粒度均匀、还原性好、高温冶金性能好、可落地贮存。 (1)机械强度高、粉末少。高碱度烧结矿主要含有机械强度高、还原性好的私结相矿物铁酸一钙,它在微观上与含铁矿物组成熔蚀或交织结构,勃结牢固。此外,总私结相量也高于自熔性烧结矿和熔剂性烧结矿。但当烧结高硅(5102>8%一10%)含铁原料时,即使烧结矿的碱度已达到1.6,但没有生成足够的铁酸一钙,由于正硅酸钙大量存在,仍有严重的自然粉化。欲获得机械强度好、粉末少的烧结矿,其碱度值应通过具体实验来确定。一般采用低硅(S 1024%~5%)铁料烧结时,碱度达到1.8~2.0即可得到机械强度高、粉末少的高碱度烧结矿。 (2)粒度均匀、还原性好。生产高碱度烧结矿时,烧结料中配入数量较多的熔剂,在烧结过程中可使私结相量增加,加上熔剂的分解,大量气体逸出,使烧结块微观结构上熔融充分、私结较好,而在宏观结构上出现大孔薄壁结构,经过破碎及多次转运,就成为粒度均匀、气孔率高、机械强度好的烧结小块。此外,由于钻结相矿物为易还原的铁酸一钙所组成,且气孔率高,因而还原性良好。 (3)高温冶金性能好。高碱度烧结矿,脉石熔点高、游离FeZO3减少、软熔性和低温还原粉化性都比自熔性烧结矿好。 (4)可落地贮存。高碱度烧结矿由于机械强度高、粉末少,不易自然粉化,因此允许短期落地贮存,以缓冲高炉检修与烧结继续生产的矛盾。 高炉使用高碱度烧结矿,有利于高炉强化生产、增加产量,降低焦比。高碱度烧结矿的缺点是含铁量有所下降(但这可由它的冶金性能的改善和减少直接入炉的熔剂量而得到补偿),烧结脱硫率降低,使其含硫量上升。 生产高碱度烧结矿的工艺要求与普通烧结矿相同,但应尽量选用品位高、含硫低的原料,加强熔剂的破碎,针对原料特点以及高炉合理炉料结构的要求,通过试验研究,选择最佳的烧结矿碱度,以保证获得应有的良好性能。 (蔡汝卓周取定)
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条