1) pressureless
无压
1.
The sialon powder was pressureless sintered at 1660℃ by general process and equipment.
以廉价的高岭土碳热还原—氮化法制得的β′—Sialon粉料为原料 ,用常规的制备工艺进行无压烧结 ,在1 660℃下烧结出体积密度近 3 2g/cm3 ,常温抗弯强度达 4 0 0～50 0MPa的烧结材
2) no-vollage and no-current
无压无流
3) Pressureless Sintering
无压烧结
1.
Preparation process of ZrB_2/B_4C ceramic composites by pressureless sintering based on mechanical mixing;
基于机械混合法无压烧结制备ZrB_2/B_4C陶瓷复合材料
2.
Research on pressureless sintering of hexagonal boron nitride;
六方氮化硼无压烧结研究
3.
Discussion on pressureless sintering of SiC ceramic;
SiC陶瓷无压烧结工艺探讨
4) confining pressure-free
无围压
1.
To solve this problem we developed a high negative pressure and confining pressure-free perforating process.
无围压射孔技术就是研究在高负压甚至无围压条件下实现射孔完井。
5) pressless sintering
无压烧结
1.
In this paper,the ZrB_2-SiC ceramic matrix composites were prepared by pressless sintering with YAG as sintering additive.
以钇铝石榴石-YAG为烧结助剂,通过无压烧结制备了ZrB2-SiC复相陶瓷。
2.
Zirconium diboride-silicon carbide (ZrB2-SiC) composites were prepared by pressless sintering with yttrium aluminum garnet (YAG) as sintering additive.
以钇铝石榴石(yttriumaluminumgarnet,YAG)为烧结助剂,通过无压烧结工艺制备了ZrB2-SiC复相陶瓷。
3.
The mechanical properties and microstructure of silicon nitride ceramics with MgO-Al2O3-SiO2 as additives produced by pressless sintering were investigated by XRD, SEM, TEM, EDS, and HRTEM.
以MgO-Al2O3-SiO2为烧结助剂,借助XRD、SEM、TEM、EDS、HRTEM等手段,研究了无压烧结氮化硅陶瓷材料的力学性能和显微结构,着重探讨了材料制备工艺、力学性能和显微结构之间的关系,通过调整制备工艺改善材料微观结构以提高材料的力学性能。
6) no-clamping marks
无压痕
1.
To meet the requirements of no-clamping marks on the surface of capacity,integrative analysis was made based on the deformations of clamp claws and capacity under driving moment,and acting and reacting forces,the relationship between the construction deformation of the claws and the clamping marks was obtained.
针对高速全自动电容生产中,要求电容夹持表面“无压痕”的情况,将夹头驱动力和电容筒反作用力共同作用下的夹头受力变形和电容筒受压变形进行了综合分析,得出了夹头爪瓣结构变形与夹持“压痕”的关系,利用该关系设计的夹头实现电容的无痕夹持要求。
补充资料：10000kN摩擦压砖机
10000kN摩擦压砖机
解‘一…释砰夔割匕二鱿
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条