1) pressure infiltration
压力浸渗
1.
The superplastic characteristics of the betaSiC whisker reinforced LY12 aluminum composite, fabricated by pressure infiltration and hotrolling after extrusion with a low extrusion ratio, were investigated The results show that the SiCw/LY12 composite exhibit a total elongation of 200%370% in the initial strain rate region from 33103 to 33102 s1at 788808
对压力浸渗、小挤压比挤压以及进一步轧制制备的β－ＳｉＣ晶须增强ＬＹ１２铝基复合材料的超塑性变形行为进行了研究。
2.
The scientific and technical matters concerned with the stability and the rheology properties of SiC slips, the packing behaviors of SiC powders, the manufacture of SiC tape and bulk skeletons, and the process of pressure infiltration were investigated.
研究了ＳｉＣ料浆的稳定性和流变特性、ＳｉＣ粉末的填实过程、ＳｉＣ薄带和骨架的制备技术、ＳｉＣ的固相烧结和骨架密度的控制，以及压力浸渗等科学问题和工艺问题。
3.
The article discussed the effect of preparing particle reinforced metal matrix composites by the path of pressure infiltration and the way of "nonuniform reinforced" to reduce the critical osmotic pressure and deformation degree of prefabricated body; and the possibility of improve plasticity and toughness of complex material to certain degree was also discussed.
本文通过“非均匀增强”的方式，探讨了用压力浸渗法制备颗粒增强金属基复合材料的途径，对减小临界浸渗压力及降低预制体变形程度的效果，以及在一定程度上改善复合材料塑性和韧性的可能性。
3) vacuum-adjustable pressure infiltration
真空变压力浸渗
1.
Preparation of high volume fraction SiC_p/Al composites by vacuum-adjustable pressure infiltration process;
真空变压力浸渗法制备高体积分数SiC_p/Al复合材料
4) deformation/pressure infiltration
变形/压力浸渗
5) vacuum pressure infiltration
真空压力浸渗
1.
The aluminum silicon carbide electronic packaging baseplates were produced successfully by combination of compression molding for SiC preform and vacuum pressure infiltration.
采用模压成形制备SiC预制件和真空压力浸渗相结合的技术,成功制备出AlSiC电子封装基片。
2.
SiCp /AZ91D composites were fabricated by vacuum pressure infiltration process, in which the SiC particles coverage method was used to protect magnesium alloy melt, and through the method, the flux inclusions easily occurred in the flux coverage process could be removed.
采用真空压力浸渗装置制备SiCp/AZ91D复合材料。
6) Vacuum-Pressure Infiltration
真空-压力浸渗
补充资料：热浸渗铝镀层
分子式：
CAS号：
性质：用热浸镀方法在钢表面形成的镀铝层。钢件浸入700～730℃的熔融铝液中，表面生成铝铁化合物，同时一部分铝原子渗入钢铁基体形成扩散层。为使镀层与基体金属牢固结合，一般在热浸后还要进行一次900～980℃的高温处理，使镀层软熔扩散，形成合金层。镀层具有优良的耐大气腐蚀性、抗高温氧化性和抗高温硫腐蚀性能。在石油、化工、能源、海洋工程等领域广泛应用。
CAS号：
性质：用热浸镀方法在钢表面形成的镀铝层。钢件浸入700～730℃的熔融铝液中，表面生成铝铁化合物，同时一部分铝原子渗入钢铁基体形成扩散层。为使镀层与基体金属牢固结合，一般在热浸后还要进行一次900～980℃的高温处理，使镀层软熔扩散，形成合金层。镀层具有优良的耐大气腐蚀性、抗高温氧化性和抗高温硫腐蚀性能。在石油、化工、能源、海洋工程等领域广泛应用。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条