说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 钢铁厂自动化
1)  automation of iron and steel works
钢铁厂自动化
2)  Power plant automation
电厂自动化
3)  substation automation
厂站自动化
1.
Loop Ethernet-networking mode for distributed substation automation system;
环形以太网——一种合理的分散式厂站自动化系统组网模式
2.
: Combined with the NSC substation automation system,the application and implementation of communication,GPS,VQC and other techniques are studied in this paper.Based on the Taihe and Tongji 220 kV substation construction in Shanghai China,the paper proposes their project diagrams and the problems met in engineering process and the solution for them are discussed in detail
结合南京中德公司 NSC 厂站自动化系统,介绍 220 kV 及以上变电站综合自动化系统中的串口通信、现场总线、局域网 3 种通信方式及同期、VQC、五防功能等。
4)  waterworks automation
水厂自动化
1.
According to the structural mode often used in the waterworks automation of China, the structuralmode of the waterworks automation based on Fieldbus is put forward and its advantages are analyzed.
根据我国水厂自动化常用的结构模式, 提出了基于现场总线的水厂自动化结构模式, 分析了该模式的优点, 论述了基于ControlNet和PROFIBUS的水厂自动化系统硬件组成和功能设置, 并给出了典型结构图, 介绍了一个基于现场总线的水厂自动化应用实例。
2.
According to the actuality of our country′s waterworks automation and combining the development of automatic control system.
根据我国水厂自动化现状,结合自动控制系统的发展,介绍一种基于LonWorks技术的水厂生产自动化管控方案。
3.
This thesis uses the CANBus as the means of communication to compose the waterworks automation monitor system that is based on the FieldBus.
本文以CAN总线作为通信手段,构成基于现场总线的水厂自动化监控网络系统。
5)  factory automation
工厂自动化
1.
Technology of Industrial Wireless Communication Chapter 13:Wireless Communication and Networking Technology for Discrete Factory Automation
第十三章 面向离散工厂自动化的无线通信及网络技术
2.
Based on the analysis of the comPOsition and characteristics of factory automation system,thecommunication requirements under factory conditions in particular the fieldbus architecture are discussed,thus a laboratory model of fieldbus network is designed and implemented.
分析了工厂自动化网络系统的组成和特点,着重讨论了工业环境下的通信需求。
3.
This paper discusses the characteristic and function of field bus control technology and analyzes its application to factory automation.
简要阐述现场总线控制技术特点及其功能,并对现场总线控制技术在工厂自动化中应用作了 具体分析。
6)  whole plant automation
全厂自动化
补充资料:后勤指挥自动化系统(见后勤指挥自动化)


后勤指挥自动化系统(见后勤指挥自动化)
automated system of logistic command

  houqin zhihui zidonghua xitong后勤指挥自动化系统(automated、ys-tem of logistie eommand)见后勤指挥自动化。
  
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条