说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 出口角
1)  Outlet Angle
出口角
1.
Testing equipment and testing method for centrifugal pump was introduced,and experimental steady-state hydraulic performance during changing outletangle was obtained through changing outlet angle and the result was discussed at the end.
介绍了离心泵性能试验的试验装置和试验方法,通过对一台离心泵的试验,给出了水泵在改变其叶轮出口角时各参数的稳态性能曲线,并对其进行了分析。
2)  discharge angle
出口角
1.
The theoretical and experimental research and the numerical simulation are introduced while the discharge angle of the vane is changed.
本论文以离心泵为研究对象,围绕离心泵在出口角改变时所表现出的稳态工作特性,对其稳态性能进行了理论分析和试验研究,并对叶轮内部流场进行了数值模拟。
3)  outlet angle
出口角度
1.
The test studies of the axial flow type gas-liquid cyclone with the outlet angles of guide vane of 15°, 20°, 25° and 30° show that in the dilute flow, the separation efficiency of guide vane with angle of 25° is the highest one, and guide vane with angle of 15° is the lowest.
导向叶片的几何尺寸是影响轴流式气液旋流器分离性能的重要因素,对导叶出口角度分别为15、20、25和30°的轴流式气液旋流器的试验研究显示,在稀相时,导叶角度25°的旋流器分离效率最高,导叶角度15°的旋流器分离效率最低,而导叶角度20和30°的旋流器的分离效率介于二者之间。
4)  outlet bending angle
出口弯角
1.
After analyzing the pressure characteristics, the velocity distribution, the interface migration and the outlet bending angle of the two melts in the bicomponent spinning, the article got a basic principle about the shaping of “islands” and its distribution in the cross section of the Sea-island fiber.
文章通过分析双组分复合纤维纺丝时两相熔体的压力特征、速度分布、界面迁移和出口弯角等熔体特征,对海岛纤维岛相成型及其在纤维横截面上分布的基本规律进行了探讨。
5)  the angle of departure
出口锥角
1.
Quite good effect is gained from broadening the angle of entry of the piercing mill and narrowing the angle of departure of the roller,by which the efficiency of piercing is increased and per unit energy consumption is reduced.
通过增大穿孔机送进角 ,减小轧辊出口锥角 ,从而提高了穿孔效率 ,降低了单位能耗 ,收到了较好的效果。
6)  inlet and outlet angle
进出口角
1.
Basing on a great deal of calculation,study how the pump structure parameters influence the performance curve of mixedflow pump, such as the adjustment of the blade inlet and outlet angle、the magnitudeof the inlet edge curvaturea.
在大量的算例的基础上,研究泵结构参数如叶片进出口角的调整、进口边的曲率大小、叶轮外径的斜切对混流泵性能曲线的影响,并且引用fluent软件进行流场的模拟,利用模拟结果得到泵的扬程以及其它相关参数,从而绘制Q-H曲线。
补充资料:口角疮

口角疮

口角疮   病名。见《幼幼集成》。即指口角生疮,多见于小儿。亦即口吻疮。详该条。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条