说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 旋转拉丝模
1)  rotational drawing die
旋转拉丝模
2)  rotary type ampoule filling and drawing-sealing machine
旋转式安瓿拉丝灌封机
3)  spin casting
旋转投丝
4)  disctype drawing
转盘拉丝
5)  Euler rotation
欧拉旋转
1.
Transformation matrix of Euler rotation of one coordinate is obtained in the other coordinate.
并且通过2个不变矢量在不同坐标系中的表达,识别了飞行器在空间绕质心旋转运动的3个欧拉旋转角。
2.
A uniform frame of the rotation transformation of the global Cartesian coordinates to the element local Cartesian coordinates is first established with the help of the Euler rotation.
首先利用三次欧拉旋转变换构造了任意三维几何载体共形天线全局直角坐标系到单元局部直角坐标系旋转变换的统一框架,并以此为基础,实现了共形天线全局极坐标系到局部极坐标系的空间旋转变换和单元极化方向图的全局旋转变换。
6)  circumgyration stretch
旋转拉伸
1.
The technique specification and operating skills in circumgyration stretch and scan sculpt in the software of CATIA V5 are introduced ambining with the design example of fluid valve revolving tie-in.
简要介绍了CATIAV5软件(简称CATIA)旋转拉伸与扫描特征造型技术的主要功能以及机械产品设计的特点,结合液压阀旋转接头设计实例对CATIA旋转拉伸造型设计的方法和要点进行了探讨。
补充资料:管材旋转模冷拔


管材旋转模冷拔
cold drawing of tube through revolving die

的主动旋转外模与顶头(或芯棒)之间拔制管材的工艺(见图)采用旋转模拉拔,拉拔的部分变形为滚轧所取代,滚珠或滚柱与管材接触表面之间为滚动摩擦。摩擦系数小,可以降低拔制力。这对薄壁管和低塑性材料的拉拔很有利。但是,旋转模冷拔管材存在以下的缺点:(1)旋转槽内滚珠或滚柱的咬入角较小(镇15。),睿二瑙 滚珠式旋转模的结构及拔管过程 l一端支持环;2一安装在旋转支持器内的模套; 3一管材;4一芯棒guaneai xuanzhuanmu lengba管材旋转模冷拔(eold arawing of:ub。thro-u只h revolving die)室温下在装有滚珠或渡杜使得每转的减壁量不能取大,一般小于滚珠或滚柱直径的2%;(2)为防止管体表面出现螺旋线,旋转模每转动一次管材的轴向送进量必须很小,对于滚珠组装的旋转模,约为管材周长的2%一4%;(3)模内相互接触的滚珠或滚柱体之间以及它们与模套之间摩擦能耗的比重也很大。由于上述原因,旋转模冷拔管材未能在大生产中广泛应用。 (周忠民)
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条