1) composite slab
叠合板
1.
Calculating method for bearing load capacity of RC invertible "T" slab-composite slab;
混凝土倒“T”形叠合板承载力的计算方法
2.
Experimental Study of Flexural Behavior of Reinforced Concrete Composite Slab with Ferrocement;
复合砂浆钢丝网叠合板抗弯性能试验研究
3.
A new type composite structure system has been designed,which consists of PK prestressed concrete composite slabs,U-shaped or invertible T-shaped precast prestressed composite beams and composite poles of precast pipes.
新型叠合结构体系由PK预应力混凝土叠合板、U形(或倒T形)预应力预制构件叠合梁、预制管叠合柱组成,具有预制构件自重较轻、便于产业化生产、受力性能合理、施工速度快等优点。
2) laminated slab
叠合板
1.
Correlation model of bending bearing capacity between prestressed slab and laminated slabs;
预应力混凝土叠合板与薄板抗弯承载力相关关系分析
2.
Experimental research on the prestressed concrete thin-hollow slab with the thickness of 80mm and its laminated slab;
80mm厚新型预应力混凝土空心薄板及其叠合板试验研究
3.
The characteristic and weakness of both traditional precast and cast in site floor are studied,the way to develop both sp precast slab and sp laminated slab is provided to meet the needs of residential building for large and nimble separated.
分析现浇板和传统预制板的特点和弱点 ,提出发展SP板和SP叠合板是住宅实现大开间、灵活隔断的有效途径之一 ,也是建筑施工实现现代化的重要内容之一。
3) combined slab
叠合板
1.
Experiments on prestressed concrete combined slab and economic analysis;
预应力混凝土叠合板的试验研究及其经济分析
2.
Creep and stresses redistribution on steel-concrete composite structure with combined slab of long span bridge;
钢-混凝土叠合板组合桥面的徐变和应力重分布研究
3.
In this paper has been reseached crack resistant performance of prestressed concrete combined slab,then gave analysis methods on crack resistant performance of prestressed concrete combined slab after superposition.
本文对预应力混凝土叠合板的抗裂性能进行了分析,提出了预应力混凝土叠合板叠合后的抗裂性能分析方法。
4) superposed slab
叠合板
1.
Taking the floor as secondary superposed slab its right section strength and the shear strength of adjoining face are checked.
对出现裂缝的某六层砖混宿舍楼的现浇楼板加一层钢筋混凝土叠合层 ,按二次叠合板对板进行了正截面强度和结合面抗剪强度验算 ,表明了楼板经整体加固后能够保证原设计的安全度 ,是切实可行
2.
The Paper explores the details and transmission Properties of joints between superposed slabs by experimental study, then suggests some rational details of joints and design method.
对叠合板板侧各种拼接缝的构造及传力性能进行了试验研究,建议了合理的整体式拼缝构造形式及计算方法。
3.
This thesis mainly discussed one type of two-way superposed slab floor with prestress in one way.
本论文主要研究单向预应力双向叠合板楼盖，其以预应力预制叠合底板为底模，利用板侧伸出钢筋的搭接实现横向传力，变单向受力为双向受力；通过二次浇筑混凝土形成整体楼盖结构；通过预制底板中单向施加先张预应力改善了楼盖的受力性能，满足了大开间及不同型式建筑的要求。
5) composite plate
叠合板
1.
Through experimental study of three double spans SFRC prestressed continuous composite plates, the influence of the reinforcing bars at the support and the steel fibers in the composite plane on the short-time stiffness in the span is analyzed A short-time flexure stiffness formula of SFRC prestressed continuous composite plates under secondary loading is presente
通过 3块 2跨钢纤维混凝土预应力连续叠合板的试验研究 ,分析了支座配筋及叠合面里的钢纤维对跨中刚度的影响 ,提出了二次受力钢纤维混凝土预应力连续叠合板的受弯短期刚度公
2.
Through the experiment study of three double spans SFRC pretressed continuous composite plates,the features of plastic moment redistribution of prestressed continuous composite plates and the factors of influencing moment redistribution are analyzed in this paper.
通过 3块 2跨钢纤维混凝土预应力连续叠合板的试验研究 ,分析了预应力连续叠合板塑性内力重分布的特点及影响弯矩调幅的因素 ,认为钢纤维混凝土的弯矩调幅值可适当地提高 ,最后提出了二次受力钢纤维混凝土预应力连续叠合板的弯矩调幅限值公式 ,为这种板的工程应用提供了依
6) SPD laminated slab
SPD叠合板
补充资料：催化叠合
分子式：
CAS号：
性质：炼油工业较早应用的工艺之一。其工艺流程简单，原料易得，产品汽油的辛烷值高。按原料组成和目的产品的不同，叠合工艺可分两类。(1)非选择性叠合，用未经分离的C3、C4液化气作原料，目的是生产高辛烷值的叠合汽油。(2)选择性叠合，用组成比较单一的丙烯或丁烯馏分作原料，生产某种特定的产品，如丙烯选择性叠合生产四聚丙烯作洗涤剂或增塑剂；异丁烯选择性叠合生产高辛烷值汽油等。
CAS号：
性质：炼油工业较早应用的工艺之一。其工艺流程简单，原料易得，产品汽油的辛烷值高。按原料组成和目的产品的不同，叠合工艺可分两类。(1)非选择性叠合，用未经分离的C3、C4液化气作原料，目的是生产高辛烷值的叠合汽油。(2)选择性叠合，用组成比较单一的丙烯或丁烯馏分作原料，生产某种特定的产品，如丙烯选择性叠合生产四聚丙烯作洗涤剂或增塑剂；异丁烯选择性叠合生产高辛烷值汽油等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条