说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 抗冲击磨粒磨损
1)  impact abrasion resistance
抗冲击磨粒磨损
1.
This paper deals with the relation of the microstructure morphology of carbon steels to its impact abrasion resistance.
本文论述了不同碳含量碳素钢的组织形态与抗冲击磨粒磨损性能的关系。
2)  impact wear
冲击磨损
1.
The impact wear behavior of AZ91D magnesium alloys in de-ionized water;
AZ91D镁合金在水介质下的冲击磨损特性研究
2.
Study on Impact Wear Properties of Composite Layer with Tungsten and Chromium;
钨铬复合铸渗层的冲击磨损性能研究
3.
TiC_p Interfacial structure and impact wear resistance of TiC p/Ni coating by laser cladding;
激光熔覆涂层中TiC_p界面结构与涂层冲击磨损性能
3)  impact abrasion
冲击磨损
1.
The impact abrasion performance of martensite steel was studied.
对马氏体细晶粒高强度钢的冲击磨损性能进行了研究。
2.
The impact abrasion properties of CrMnMo martensitic liner board steel and CrNiMo martensitic liner board steel were tested with MLDF-10 wear tester in acid-ironstone slurry.
采用MLDF-10冲击腐蚀磨损试验机研究了CrMnMo马氏体衬板钢和CrNiMo马氏体衬板钢在铁矿石酸性矿浆中的冲击磨损特性。
3.
The impact abrasion tests were performed,and both hardness and wear loss of the samples were compared with classical surfacing electrode D256.
经过对制备的试样分别进行多次冲击磨损试验,并与D256焊条进行对比试验,分析试样的硬度和磨损失重变化,结果表明,此种堆焊材料具有焊接工艺性好、堆焊层组织加工硬化率高和耐凿削式冲击磨损性能优异的特点。
4)  impact abrasive wear
冲击磨料磨损
1.
The impact abrasive wear properties of low-carbon high alloy steel were tested under the experimental condition,and then the digital simulation experiment of this test was done with the finite element analysis software ANSYS in virtual environment.
在实验室条件下对低碳高合金钢进行了冲击磨料磨损试验,然后运用ANSYS有限元分析工具,在虚拟环境下对该试验进行数字仿真,通过分析冲击磨损形貌、亚表层金相以及数字仿真所得到的冲击过程中材料的应力分布情况,讨论了试验中观察到的白层的形成机制和失效模式。
2.
Through the researches in some material's properties to resist impact abrasive wear, optimized 20CrMnTi optimized was further tested under the condition of impacting ? wear, sliding abrasive wear and impact abrasive wear, analyzed its characteristics, and discussed the appearance and forming mechanism observed.
通过对多种材料在不同试验条件下耐冲击磨料磨损性能的初步研究 ,优选出 2 0CrMnTi材料开展了在冲击磨损、滑动磨料磨损和冲击磨料磨损条件下的进一步试验 ,分析了在各磨损与变形条件下的特点 ,对所观察到的现象与机理进行了讨论 ,得出了一些有益结论。
3.
The impact abrasive wear behavious of super-high manganese steel were investigatedthrough dynamic abrasion test and hardness measurement, and by using SEM and TEM the worn surfacemorphology and microstructure observed.
本文通过动载磨料磨损实验和硬度测量,利用SEM和TEM观察磨损表面形貌和微观组织,研究了超高锰钢的冲击磨料磨损行为。
5)  wear impact energy
磨损冲击功
6)  abrasive wear
磨粒磨损
1.
Study on abrasive wear resistance of boronized layer eutecticumed with laser;
激光共晶化渗硼层磨粒磨损试验研究
2.
Research on abrasive wear of cladding metal of flux cored wire for repairing of pedrail engineering machine;
履带式工程机械行走系修复用堆焊药芯焊丝磨粒磨损性能研究
3.
Two body abrasive wear mechanism of TiNi SMA;
TiNi 系形状记忆合金两体磨粒磨损机制研究
补充资料:抗冲击强度
分子式:
CAS号:

性质:造纸工业主要用来表明纤维纸板包装箱对冲击应力的抵抗能力,同时也反映包装箱和内包装对货物的保护性能。它是使用一种特制的倾斜板冲击量测定器,在特定条件下进行检验,特别适合用于大型重负荷包装箱的检测。是模拟实际搬运和运输中所受冲击的情况,因而检验结果对实际应用颇有参考意义。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条