说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 轧线
1)  rolling line
轧线
1.
Computer dynamic simulation system for the process designing scheme of slab yard and rolling line of hot strip mill;
热轧带钢厂板坯库及轧线工艺方案计算机动态模拟系统
2)  rolling curve
轧制曲线
1.
The relationship of radial and axial feed distribution for the radial/axial rolling process of ring with rectangle cross-section was established according to the rolling curve.
为了提高环件双向轧制过程中运动学方程的精度和计算效率,根据轧制曲线建立了矩形截面环件径/轴双向轧制过程中径向与轴向进给量之间的关系。
2.
This topic mainly makes full use of the theory of node curve in closed condition and theory of instantaneous transmission to ratiocinate the rolling curve equation of the ellipse in polar coordinates format.
推导了以极坐标表示的椭圆轧件楔横轧轧制曲线方程,为轧件成形提供了理论依据,扩展了非回转轧件轧制的范围。
3)  high-speed wire mill
高线轧机
1.
The result shows that production of high strength screw bars is reasonable by the control rolling and control cooling process on high-speed wire mill with the capacity of low temperature rolling.
通过采用控轧控冷工艺,对在高线轧机上用普碳钢生产KL400Ⅲ级螺纹钢筋进行探讨,经试轧,生产出Φ8mm的KL400Ⅲ级螺纹钢筋。
2.
The two million tons high-speed wire mill in Beiying Steel Plant is designed to be high-single-line continuous high-speed wire rod mill.
北营钢厂200万t高线轧机设计为单线全连续式高速线材轧机,作为轧钢I类设备,安装精度要求高。
4)  rolling line
轧制线
1.
Therefore,based on the thoughts taking the centerline of the entry guide as the basis and using the pass for spotting to carry out uniform rolling line,the fixed guide fittings,which separate from the rolling mill,are designed.
为此,采用以进口导卫中线为基准、用孔型找正、实现轧制线统一的改进思路,设计了与轧机本体分离的固定导卫装置。
2.
The principle and composition of the cold roller rolling line automatic positioning system are analysed in detail.
详细分析了冷轧制线自动控制系统的组成及工作原理,并且给出系统的控制策略,讨论系统的控制精度
3.
On the strip steel rolling line and finishing line,the circular shear and its terminal equipments play an important role on the quality of strip steel edge.
在带钢轧制线和精整线上,圆盘剪及其前后设备对带钢的边部质量起着决定性的作用。
5)  WIRE MILL
线材轧机
1.
This paper simply analyzes five kinds of present domestic wire mill models Reasonable selection conditions are pointed out from the viewpoint of the combination of technology with economy and market
简要剖析了目前国内5种线材轧机模式,从技术与经济,市场相结合的角度,指出其合理的选用条件。
6)  mill temperature
轧线温度
补充资料:轧制线


轧制线
rolling line

  ZhQZhiXIQn轧制线(rolling line)沿车。棍上的车L制面铅垂方向配置孔型的一条水平基准线。当轧制线的位置确定之后,即可将孔型图上的孔型中性线与之重合,将孔型画到配辊图上去。(见轧辐孔型设计)采用“压力”轧制(见上压)时,轧制线所处的位置由所采用“压力”的方向和大小来决定。当采用△刀的上压值时,。.,._.,.、,。一‘.一、_△D,,、.,~~._,_一一~轧制线在乳辐中线下方二分二处;当采用△刀的下压值,.’卜切一刊一’一’一’一~’~4~,一’一“—”碑’一一 、.‘_,,.、,_~一._二,、,、△刀.,、.,一~~一,__二时,轧制线在轧辊中线上方竺井处。当不采用“压力”时,’,7一,“’~~、~,,’~’一、一一4一“一”一厂’一‘’轧制线和乳棍中线重合。 (胡林)
  
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条