1) Surface bond rate
界面结合率
2) interfacial bonding
界面结合
1.
The reason is believed to be the improved interfacial bonding.
研究表明，在碳化硅复合材料表面化学镀一层镍，能够较好地改善增强体与基体的界面结合，使得碳化硅复合材料的抗弯强度、冲击韧性及宏观硬度均有了明显的提高。
2.
The fracture surface of the wires studied by scanning electron microscopy (SEM) shows a suitable interfacial bonding between the fiber and aluminum.
复合丝拉伸断口的扫描电镜（ＳＥＭ） 观察可见断面有一定起伏，部分纤维拔出但长度较短，表明纤维与基体具有适当的界面结合。
3.
Al/Diamond composites were fabricated by Spark Plasma Sintering(SPS) under Solid-phase sintering,changes of interfacial bonding during sintering process were investigated mainly.
使用放电等离子烧结(SPS)固相烧结条件下制备Al/Diamond复合材料,重点研究烧结过程中基体与增强体两相界面结合状态随烧结时间的变化规律。
3) interface
[英]['ɪntəfeɪs] [美]['ɪntɚ'fes]
结合界面
1.
The interface between Ga_(95.
15Sn合金与Cu基体的结合界面进行了分析。
4) bonding interface
结合界面
1.
Bonding ability of TA2 and 316L plates with explosion cladding was evaluated,the microstructure and composition of the bonding interface was investigated by SEM,EDS and XRD.
结果表明,结合区形貌呈波状,结合界面附近形成细晶区;结合区存在不连续的熔合层,该层含有大量金属基体小碎块和合金化后生成的金属间化合物,并产生了裂纹、气孔,且波状结合界面不同位置组织成分分布不均匀等焊接缺陷;两基板之间发生了元素扩散;拉剪实验各项性能满足复合材料使用要求,拉伸后波状界面发生了分离。
2.
(1)We have found and defined three kinds of bonding interfaces:big wavy,small wavy and micro wavy,and the micro wavy interface is the best,in a cladding plate,it is for the first time to find that the form of interface presents regular distribution.
爆炸焊接理论与技术取得了四个方面的进展:(1)发现并重新定义了三种结合界面:大波状、小波状和微波状,其中以微波状为最佳。
3.
The bonding interface of TA1/Q235 and the diffusion of Ti and Fe are investigated by the manufacture of TA1/Q235 with ARB process.
通过TA1/Q235的累积叠轧焊,研究TA1/Q235复合板结合界面组织和Ti与Fe两元素的扩散情况。
5) interface bonding
界面结合
1.
The changes of the surface smooth degree and the interface bonding after the level off rolling were investigated.
研究了高温平整轧制前后钢带表面平整度及界面结合情况的变化 ,并进一步探讨了轧制参数对界面结合强度的影响·分析了带坯复合界面的演化机理·结果表明 :平整轧制可明显改善钢带表面的平整度 ,提高界面结合强度 ;轧制温度、轧制压下量等工艺参数对界面结合有较大影响 ,而轧制速度影响不大 ;平整轧制时 ,反向凝固带坯复合界面发生演化 ,使界面结合增强 ,其机理为咬合机制、互扩散机制及固溶作用机制
2.
The influence of laser power and scanning velocity on interface bonding between clad layer and substrate and uniformity of microstructure in composite surface layer was studied.
研究了激光功率、扫描速度对原位合成TiCp/Al表层复合材料与基底的界面结合和熔覆层组织均匀性的影响。
3.
In this paper, it is mainly from dispersion and interface bonding point of view suggested that the multi-walled carbon nanotubes (MWNTs) were filled into polymer matrix.
本文主要从分散和界面结合的角度出发研究了多壁纳米碳管(MWNTs)与聚合物的复合，通过对复合材料微结构和力学性能的表征，分析了碳管在聚合物中的作用机理。
6) interface binding
界面结合
1.
This paper is focused on improving the interface bonding strength of hard grain phase and copper alloy matrix in the WC particle reinforced composite to raise its wear resistance, and revealing the relationship between the wear resistance and interface binding, the wear resistance and microstructure, and the wear resistance and abrasion mechanism.
为了提高硬质颗粒复合合金材料的耐磨性并揭示其与界面结合、微观组织及磨损机理之间的关系,本文设计并通过钎焊法,在普通铸钢件表面制得了厚度可达30mm的WC颗粒增强铜基合金覆层,测试分析了上述各种因素对此覆层耐磨性的影响。
补充资料：蛋白结合率
蛋白结合率
药物在体内吸收进入血液后，能程度不同地与血浆蛋白(主要为白蛋白)进行可逆性结合，这种结合能力称为蛋白结合力，以百分率来表示，称为蛋白结合率。与血浆蛋白结合的药物暂时失去药理活性。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条