说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 传质单元
1)  transfer unit
传质单元
1.
The author uses the principle of coordinate trnsformation to develop a new equation for the calculation of the number of transfer units in a packed distillation column.
利用坐标变换原理,导出了计算填料精馏塔传质单元数的新公式。
2)  number of transfer unit
传质单元数
1.
With an example of the number of transfer unit of extraction column,diagramming integration is realized in Excel with the share number-n.
以化工实验中的萃取塔传质单元数为例,选择不同的等份数n,实现了图解积分法的Excel计算,允许精度范围内得到了计算量最小的n值及相应的萃取塔传质单元数。
2.
By use of the formula and copying function of Excel,the number of transfer unit can be easily resulted.
根据填料吸收塔传质单元数几何意义,将不规则图形的面积转换成多个梯形面积之和,再利用Excel的公式和复制功能,大大简化了传质单元数的求解过程,同时还获得了吸收塔不同高度处的气液浓度和传质推动力等数据。
3)  height of mass transfer unit
传质单元高度
1.
In Φ50mm packed extraction columns,two extraction systems with different interfacial tensions,kerosene-benzoic acid-water and 30%TBP(kerosene)-acetic acid-water were chosen to examine the Hoxp(height of mass transfer unit based on plug flow and continuous flow) of this structured packing and Φ10mm Pall ring packing under various operation conditions.
在Φ50mm的填料萃取塔中,选用煤油–苯甲酸–水和30%TBP(煤油)–乙酸–水两种不同界面张力的物系,测定了该填料和Φ10mm的鲍尔环填料在不同操作条件下的表观传质单元高度。
2.
Results show that H oxp (height of mass transfer unit based on plug flow and continuous flow) of conjugate ring is bigger than that o.
在120的不锈钢填料塔中,以16共轭环塔填料为研究对象,分别选用正丁醇-丁二酸-水和30%TBP(磷酸三丁酯)的煤油-醋酸-水2种不同界面张力的体系进行试验,测定了该填料在不同两相流速下的表观传质单元高度,和相同条件下测定的同尺寸鲍尔环、拉西环和θ环作了比较,θ环的表观传质单元高度(Hoxp)比共轭环小,但共轭环的(Hoxp)分别比鲍尔环小16%,比拉西环小25%。
3.
InΦ50 mm packed extraction columns, two extraction systems with different interfacial tension, kerosene-benzoic acid-water and 30%TBP(kerosene)-acetic acid-water were chosen to examine the dispersed phase holdup fraction, flooding velosity, H_(oxp) (apparent height of mass transfer unit based on plug flow and continuous flow) of structured packi.
4 mmθ环填料在不同操作条件下的分散相存留分数、液泛速度和表观传质单元高度。
4)  mass transfer unit modeling
传质单元模型
1.
According to the principle of the horizontal cylinder desolventizer (HCD) with indirectheating surfaces of inside and outside surfaces, a mass transfer unit modeling was proposed.
根据卧式内外间接加热脱溶器(HCD脱溶器)的工作原理,建立了HCD脱溶器的传质单元模型。
5)  number of elements of gas phase mass transfer
气相传质单元数
1.
This article introduces us two kinds on how to solve the number of elements of gas phase mass transfer new method.
本文介绍了两种计算气相传质单元数NOG的新方法 ,即梯级迭代法和梯形公式法 ,其主要特点是概念清晰 ,过程简洁 ,结果准确。
6)  number of liquid transfer units
液相传质单元数
1.
In this paper, various calculating formulas of the number of liquid transfer units are proposed in terms of absorption and desorption of low concentration gas.
导出不同情况下低浓度气体吸收、解吸时的液相传质单元数的计算公式 ,并与 Colburn传质单元数算图进行比较 。
补充资料:传质单元高度
      在逆流操作的微分接触传质设备中,使浓度变化达到传质单元数为 1所需的设备接触传质段高度。传质单元高度综合反映了设备的传质特性,可根据两相的流量和传质总系数分别用下式计算:
  
    式中(HTU)和(HTU)分别为用x相和y相参数表示的传质单元高度;Cx和Cy分别为两相的摩尔流率;KOx和KOy分别为以x相摩尔分率差和y相摩尔分率差为推动力的两相的传质总系数;α为比表面积,即单位设备体积的传质面积。传质单元高度的概念,广泛应用于吸收、萃取和精馏等的设计计算中。已知传质单元高度和传质单元数,其乘积即为完成给定分离任务所需的设备接触传质段高度。两相流速有变化时,传质系数的变化较大,传质单元高度的变化较小。因此,在逆流操作的微分接触传质设备的放大设计时,采用传质单元高度的计算方法,较为方便和可靠。
  
  传质单元高度由实验测定,它与设备结构、物系性质以及两相流速等因素有关,变动范围很大。吸收用的填充塔,其传质单元高度多为0.5~1.5m,用于精密精馏的填充塔或膜式塔,其传质单元高度较小,有的仅为几厘米。
  

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条