说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 有序畴尺寸
1)  ordered domain size
有序畴尺寸
1.
The degree of ordering and ordered domain size in Ni3Al solid solutionprepared by SHS have been determined with XRD.
用X射线衍射法测定自蔓延高温合成(简称SHS)Ni3Al固溶体有序度和有序畴尺寸,结果指出:待反应混合物成形压力越大,有序度越高,有序畴尺寸越大。
2)  phase size
相畴尺寸
1.
Special attention is paid to the efficts of molecular weight and concentration of the compatibilizers on the interfacial tension,phase size and coalescence in the polymer blends.
重点介绍了增容剂的分子量、用量对聚合物共混物的界面张力、相畴尺寸和聚结的影响。
3)  micro-strain
晶畴尺寸
1.
The effects of heat treatment temperatures and doping elements (Ti, Zr) on grain domain size and micro-strain in powder MgB-2 have been investigated by using X-ray and SEM.
用X射线衍射仪和扫描电镜研究了热处理温度和添加元素(Ti,Zr)对单相MgB2 粉末样品的晶畴尺寸和微观应变的影响 。
4)  procedure size
工序尺寸
1.
Based on the influence factors of location error in clamping apparatus design this paper has established the relation function between the procedure sizes or angles and the location norm parameters in which the positioning error substituted by the approximate differential value of function.
从分析夹具设计中定位误差的影响因素入手,建立了工序尺寸或角度与定位基准有关量的函数表达式,进而由函数的微分近似代替定位误差。
2.
Based on the Influence factors of location error in clamping apparatus design, this paper has established the relation function between the procedure sizes or angles and the location norm parameters, in which the positioning error substituted by the approximate differential value of function.
分析夹具设计中定位误差的影响因素,建立了工序尺寸或角度与定位基准有关量的函数表达式,由函数的微分近似代替定位误差。
5)  working procedure dimension
工序尺寸
1.
According to the shortest route principle of dimension chains,this method should start from the two ends of designing dimension or processing margin and track from the surface of components till closing,then find its dimension chain and calculate its working procedure dimension and allowance.
通过实例介绍工序尺寸的换算方法:跟踪图解法。
6)  procedure dimension
工序尺寸
1.
This paper focus on the proper and complete dimensioning of the tolerance of procedure dimension.
针对如何确切、完整地标注工序尺寸公差带的问题进行探讨。
补充资料:工程图标准尺寸及坐标尺寸

标准标注类型,是我们常用的标注类型。而坐标标注是便于数控加工采用的另一中标注形式。PRO/E可以将两种标注方式进行转换。


· 3.2 标准标注到坐标标注的转换


注意: 转化为坐标标注的尺寸必须是线性标注的,下列尺寸不能转化为坐标标注:


 



  • 被显示成线性尺寸的直径
  • 中心线尺寸

 



  1. 选择MODIFY DRAW > Dim Params > Dim Type > Ordinate Dim > Create Base.
  2. 选择作为参考基准线的尺寸
  3. 选择基准的引出线,该点为0点
  4. 选择 MOD DIM TYPE > Lin to Ord .
  5. 选择线性尺寸:注意:必须选择具有相同基准的尺寸

========>>>>

· 3.3 由坐标标注到标准标注的转化

1. 选择 DIM PARAMS > Diam Dim Type .


2.点击Ord to Lin


3.选择尺寸即可

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条