1) compound out situ
离位复合
1.
Al 2O 3/YSZ composites were fabricated using aqueous gel-casting compound out situ technique.
采用水基料浆注模、凝胶离位复合法制备Al2 O3 /YSZ材料 ,工艺关键是高质量水基料浆的配制、注模和凝胶固化的物理—化学过程的控制。
2) direct cyclopexy
睫状体脱离缝合复位术
1.
Analysis of the cause to ocular hypertonia after operation of direct cyclopexy for traumatic cyclodialysis;
外伤性睫状体脱离缝合复位术后高眼压的原因分析
3) centrifugal compound
离心复合
1.
Regarding to the shoulder shedding and break phenomena of the hot rolling centrifugal compound semi-steel back up roll,the analysis,in which the aspect of chemical composition,hardness,and metallographic phase,etc.
针对热轧离心复合半钢支承辊肩部脱落断裂现象,从化学成分、硬度、金相等方面进行了分析。
4) compound ion
复合离子
1.
In order to solve the problems as high mud density and low penetration rate as well as difficulty in treating mud, meeting with in drilling at the area with abnormally high pressure, this paper puts forward a new method for treating heavy mud by use of compound ion-type polymer.
本文提出了用复合离子型聚合物处理重泥浆的新方法,经室内试验和现场初步实践,取得较好效果,可供现场参考。
2.
A comprehensive indoor experiment and application at well-site were done for the compound ion polymer drilling fluid.
本文对复合离子聚合物钻井液做了较全面的室内试验和现场应用。
5) complex ions
复合离子
1.
A new lead-free piezoelectric ceramics of Bi1/2Na1/2Ti1–x(Zn1/3Nb2/3)xO3(abbreviate as BNTZN—100x) were prepared by the two-steps synthesized method and the effect of B-site the complex ions-(Zn1/3Nb2/3)4+ substitution amount on the piezoelectric and dielectric properties was investigated.
研究了B位复合离子(Zn1/3Nb2/3)4+取代量对BNT陶瓷介电及压电性能的影响。
2.
A new kind of lead-free piezoelectric ceramics of Na1/2Bi1/2Ti1-x(Ni1/3Nb2/3)xO3 is prepared by the two-step synthesis method and the effect of the B-site complex ions substitution on the piezoelectric and dielectric properties is investigated.
研究了B位复合离子取代对NBT陶瓷晶体结构及压电、介电性能的影响。
3.
A new lead-free piezoelectric ceramics of Bi1/2Na1/2Ti1-x(Mg1/3Nb2/3)xO3 was prepared by the two-step synthesize method and the effect of B-site the complex ions substitution on the piezoelectric and dielectric properties was investigated.
研究了B位复合离子取代对BNT陶瓷的晶体结构及压电与介电性能的影响。
6) compound isolation
复合隔离
1.
The construction of the compound isolation circuit with inverse transformation is introduced.
介绍了复合隔离型逆变电路的电路结构,分析了电路的工作原理和安全高效的突出特点,给出了有关计算方法,详细介绍了该电路在充电装置中的应用。
补充资料：离位
1.离开本位﹑职守。 2.伤科病症名。即脱臼﹑脱骱。指组成关节的骨端脱离其正常位置。一般由外伤引起﹐多发生于肩﹑肘关节。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条