说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 剖胸手术
1)  Thoracotomy [英][,θɔ:rə'kɔtəmi]  [美][,θorə'kɑtəmɪ]
剖胸手术
1.
【Methods】Sixty patients underwent unilateral thoracotomy were randomly allocated into three groups.
目的:评价肋间神经冷冻对剖胸手术的术后镇痛效果。
2)  Thoracotomy [英][,θɔ:rə'kɔtəmi]  [美][,θorə'kɑtəmɪ]
剖胸术
1.
Comparison between the effect of intercostal nerve block using methylene blue and that of continuously epidural analgesia after thoracotomy;
剖胸术后美蓝肋间神经阻滞镇痛与硬膜外镇痛的比较
3)  Thoracotomy [英][,θɔ:rə'kɔtəmi]  [美][,θorə'kɑtəmɪ]
剖胸术后
1.
Nosocomially Acquired Pneumonia after Thoracotomy:Analysis of Affected Factors;
剖胸术后院内获得性肺部感染的影响因素
4)  emergency thoracotomy(ET)
紧急剖胸术
1.
Objective To analyze the application of emergency thoracotomy(ET) in patients with severe thoracic trauma.
目的探讨紧急剖胸术(emergency thoracotomy,ET)在严重胸部创伤中的应用价值。
5)  thoracic surgery
开胸手术
1.
Objective Objective To observe the preemptive analgesic effects of flurbiprofen axeil on patient-controlled intravenous analgesia(PCIA) with fentanyl in patients received thoracic surgery.
方法30例ASAⅠ~Ⅱ级择期行开胸手术患者,随机均分为观察组和对照组,各15例。
2.
Methods Forty ASA Ⅰ~Ⅱ patients with lung cancer or esophageal carcinoma undergoing thoracic surgery were randomly divided into two groups:Group T receiving 10mg/kg tranexamic acid as a bolus before skin inciscion and 1mg·kg~(-1)·h~(-1) during surgery,Group C receiving isotonic saline infusion instead(n=20 in each group).
目的评价氨甲环酸在开胸手术中的止血作用和对开胸手术围术期凝血纤溶功能的影响。
3.
Objective To study the effects of preoperative visits on patients receiving ope n thoracic surgery.
目的探讨术前访视对开胸手术患者的效果。
6)  thoracic surgery
胸部手术
1.
The clinical use of micro-traumatic thoracotomy in thoracic surgery;
微创开胸技术在胸部手术中的临床应用
2.
Effort of postoperative controlled epidural analgesia on postoperative pneumonia in patients underwent thoracic surgery;
胸部手术后硬膜外自控镇痛对术后肺部感染影响的研究
3.
Objective:To search for the clinical advantages and experience of micro-traumatic thoracotomy in thoracic surgery.
目的:探讨微创开胸技术在胸部手术中的应用价值和经验。
补充资料:全面解析在AutoCAD中模型的半剖.全剖.局部剖
在cad如何做些剖切呢.今日写了一个教程,抛砖引玉,希望给大家点思路.随便做了一个模型,下面就来发张图片


图1



图2



    用剖切面完全剖开机件所得的剖视图称为全剖视图。全剖视图用于外形简单内部结构较复杂且不对称的机件。


    全剖.操作要点:xy,.XZ,YZ等平面的剖面都是依据你的ucs坐标来的,因此如果某些时候剖切得不到全剖效果的话,那就你的坐标系有问题.



图3



    最后选择b,保留两侧,得到全剖效果



图4



图5



半剖模型:


  当机件具有对称平面时,在垂直于对称平面的投影面上投射所得的图形,以对称中心线为界,一半画成剖视图,另一半画成视图,这种剖视图称为半剖视图。半剖视图适用于内外结构都需要表达且具有对称平面的机件。


  画半剖视图应注意:


  (1)视图和剖视的分界线应是细点画线,不能以粗实线分界。


  (2)半剖视图中由于图形对称,机件的内部形状已在半个剖视图中表示清楚,所以在表达外部形状的半个视图中不画虚线,以及在后方不可见的虚线都不画。


  (3)机件的形状接近于对称,且不对称部分已另有图形表达清楚时,也可以画成半剖视图。


  (4)当对称机件的轮廓线与中心线重合时,不宜采用半剖视图表示。


  半剖的操作与阶梯剖有点相似.只不过阶梯剖的要做多条辅助线



图6



图7



局部剖:


  用剖切面局部地剖开机件,以波浪线或双折线为分界线,一部分画成视图以表达外形,其余部分画成剖视图以表达内部结构,这样所得的图形称为局部剖视图。它用于内外结构都需要表达且不对称的机件。


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条