1) circuit protector against power failure
掉电保护电路
1.
It puts forward solutions to a series of problems including the instability of the dripping speed,the vibration,the controlling stagnancy of the stepping electric motor and the circuit protector against power failure.
介绍了一种静脉输液控制器的硬件结构和软件的设计 ,对出现的滴速不稳、抖动 ,步进电机的控制迟滞及掉电保护电路等问题提出了独到的解决方案。
2) power down protection
掉电保护
1.
Puts forward the purpose & necessary on power down protection of NC system for machine tool,and emphasis on discussing it's method of software realization,low speed wire electrical discharge machineing(LSWEDM)machine tool for example.
提出了机床数控系统掉电保护的目的、必要性,并以低速走丝电火花线切割机为例,重点论述了机床数控系统掉电保护的软件实现方法。
2.
The file access control,message authentication and data encryption for communication were designed,and the power down protection while modifying flash memory or update several files was introdued.
对CDMA2000网络分组数据业务中智能卡芯片操作系统的安全模块进行了体系结构设计,对网络接入认证鉴权算法进行分析并优化实现,对文件访问控制、报文鉴别、数据加密通信等进行设计,引入Flash改写及多个文件擦写的掉电保护机制。
3) power-off protection
掉电保护
1.
The hardware design scheme and software programming method for general power-off protection of measuring control system are introduced.
提出了掉电后继续工作时间可设定的思想和新的掉电监测方法 ,介绍了测控系统可靠掉电保护硬件设计方案和软件编程思想。
4) power-fail protection
掉电保护
1.
This paper describes the makeup and working principle of MAX691A supervisor circuits, and its application to the anti-interference and power-fail protection circuit of the 80c196kc single-chip micro controller system is presentedalso, as well as the hard ware connection circuit and the corresponding software design method .
介绍了MAX691A微处理器监控电路的组成和工作原理,并在80c196kc单片机应用系统中,给出了一种用该系列芯片组成的抗干扰与掉电保护电路,详细描述了硬件连接电路和相应的软件设计方法。
2.
By analyzing and contrasting several power-fail protection circuits in SCM,the paper puts forward a simple and reliable power-fail protection scheme for SCM.
通过对几种掉电保护方法的分析对比,给出了一种简单可靠、通用于单片机系统的掉电保护电路;详细地介绍了单片机掉电保护电路的设计原理及硬、软件实现方法,分析了其可靠性。
5) holding circuit of losing electricity
掉电保持电路
6) Data protection
掉电数据保护
1.
With respect to the problem of data loss in SRAM of CMOS,this paper introduces a kind of data protection circuit by postponing integral calculus.
针对CMOS型SRAM存储器在掉电时数据易失的问题,设计了一种在高要求应用系统中通过积分延时的掉电数据保护电路。
补充资料:集成电路继电保护装置
集成电路继电保护装置
integrated-circuit relay protection equip-ment
正、负电源引出端。有的运算放大器还有调零和连接消除自激的补偿电容的端子. 等效电路图1(a)是运算放大器的等效电路。U、所在输人端叫做反相拾人端.U,所在箱人端叫做同相输人端。输人阻抗是一个电阻网络,有差模(信号加在两输人端子之间)和共模(信号同时加在两翰人端子和┌─┐│ │└─┘ 图1运算放大器的等效电路和墓本电路(a)等效电路;(b)负反馈反相放大器;(c)负反债同相放大祥;(d)负反馈差动放大器.(e)加法界;(f)积分界;(g)徽分异;(h)移相器;(i)多反馈环形澳波器;(j)半波整流电路;(k)交流波一方波变换器,(l)反 相褚入继电触发界;(m)同相抢入继电触发器开环工作的差动放大器,用来比较两个直流信号的大小,抽出正或负饱和电压.如果待比较电压中的一个是固定的今考电压,比较器就成为一个电平检测器. 在电平检洲器电路中加人正反该,就成为具有继电特性的触发器.图1(l)和图1(m)是两种输出正信号的继电触发器。图1(1),当e,
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条