1)  Transsphenoidal surgery
经蝶窦鞍内手术
2)  Transsphenoidal
经蝶
1.
Till 1960 s,Hardy used operating microscope for transsphenoidal pituitary adenomectomy.
研究背景经蝶窦垂体瘤切除术始于1907年(Schloffer),但由于当时照明不良、手术部位深在、显露不佳、止血困难、术后易发生脑脊液漏及难以控制的颅内感染等原因,在此后相当长的一段时期内,一直未得到广泛应用。
3)  Transsphenoidal surgery
经蝶手术
1.
Endocrinological evaluation for Cushing disease treated by transsphenoidal surgery: a follow-up study;
经蝶手术治疗Cushing病后的内分泌随访观察
2.
Risk factors for cerebrospinal fluid rhinorrhea following transsphenoidal surgery for large and giant pituitary adenomas;
大型及巨大型垂体腺瘤经蝶手术术后脑脊液鼻漏的危险性因素分析
3.
Objective To explore factors influencing the recurrence of patients with Cushing s disease after transsphenoidal surgery.
目的探讨可能影响库欣病经蝶手术后复发的因素。
4)  Transsphenoidal approach
经蝶入路
1.
Aim: To explore the modified incision of transsphenoidal approach.
目的:探讨经蝶入路手术切口的改进方法。
2.
Methods: Ten fixed cadavers heads (six male, four female), the arteries of which were injected with red latex, were used to perform transsphenoidal approach.
目的:对经蝶海绵窦手术中相关动脉结构的解剖学数据和形态学特点进行研究,为临床手术提供解剖学基础;方法:取动脉灌注的固定尸头标本10例20侧(6男4女),通过经蝶手术暴露鞍旁段颈内动脉(PSICA)后,小心分离各动脉分支,对其进行解剖学描述,并和经颅手术中海绵窦内血管结构进行对比;结果:经蝶入路颈内动脉可分为PSICA和斜坡旁段颈内动脉(PCICA),打开海绵窦下壁即暴露PSICA,根据其形态可分为上、下水平部和垂直部,脑膜垂体干源于PSICA下水平部末段内壁占45%(9侧)、顶壁占20%(4侧)、外壁占25%(5侧)、上水平部中段内壁占10%(2侧);海绵窦下动脉源于PSICA垂直部中段外壁占80%(16侧),下水平部中段占5%(1侧);另15%(3侧)源于脑膜垂体干;仅在25%标本(5侧)中发现McConnell’s背囊动脉,其源于垂直部上段的内壁上,口径细小(0。
3.
Objective To introduce surgical experience and the advantages of transsphenoidal approach via single nostril and posterior section of perpendicular plate of the ethmoid bone for resection of pituitary adenoma.
目的 介绍、推广单鼻孔直入经筛骨垂直板后段经蝶入路切除垂体腺瘤的手术经验,探讨该术式的优越性。
5)  Transsphenoidal
经蝶窦
1.
Transsphenoidal microsurgery for male patients with prolactinoma:results of long-term follow-up;
经蝶窦显微手术治疗男性泌乳素腺瘤的长期随访分析
6)  Transsphenoidal approach
经蝶路径
参考词条
补充资料:经皮经颈静脉肝内门体静脉内支架分流术


经皮经颈静脉肝内门体静脉内支架分流术


介入放射学技术。也称经皮经颈静脉肝内门体静脉分流术(TIPS),1969年最初由Rosch等首先报道。经颈静脉送入导丝,于门-腔静脉间经肝实质建立通道,并放入支架以形成永久性分流径路的治疗方式,以降低门脉压力,治疗顽固性的食管胃底静脉曲张出血及顽固性的腹水。该技术除常规导丝、导管、球囊扩张导管等外,需向建立的分流通道内置入支架,常用的有Z-型支架、Wallstent支架、Strecker支架等。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。