说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 直流光电电流互感器
1)  direct current optical-electronic current transformer
直流光电电流互感器
1.
This paper introduces the principle and actual operating environment of the direct current optical-electronic current transformer that is the first one in China.
介绍了国内首台直流光电电流互感器的工作原理和实际运行情况,提出了直流光电电流互感器现场校验方法;结合实际运行测试结果进行了误差分析,给出了进一步的完善方法。
2)  dc optical current transducer
直流光学电流互感器
1.
Focusing on the research of improving the output signal to noise ratio of DC optical current transducer,this paper introduces the principle of DC optical current transducer which based on Faraday Magneto-optic effect.
针对提高直流光学电流互感器的输出信噪比展开研究。
3)  direct current transformer
直流电流互感器
1.
This paper introduces a kind of SF6 gas insulated,500 kV direct current transformer,which is based on the principle of transductor.
我国直流输电线路及换流站的数量及发展速度在世界上处于领先地位,但是作为直流电网电量监测及保护的重要设备,直流电流互感器却存在许多问题,故障率很高。
4)  electro-optical type current transformer
光电电流互感器
1.
The measure sensor,Rogowski coil is the key part of the electro-optical type current transformer.
测量传感头Rogowski线圈是光电电流互感器的关键部分。
2.
Here the article introduces a working principle and systematic composition of a new type electro-optical type current transformer based on ROG.
现介绍一种基于ROGOWSKI线圈原新型光电电流互感器的工作原理及系统的组成。
5)  optical current transformer
光电电流互感器
1.
AD7656 and its application in optical current transformer
AD7656及其在光电电流互感器中的应用
2.
The Field Programmable Gate Array (FPGA) technology has been used for designing the signal processing circuit of A/D device, CRE code and Manchester module of high -voltage side for optical current transformer in this paper.
本文采用现场可编程门阵列(FPGA)技术进行光电电流互感器高压侧信号处理电路中的模数转换器控制、CRC校验码及曼切斯特编码模块的电路设计。
6)  DC voltage transformer
直流电压互感器
补充资料:直流电流互感器
      用于直流电流量值变换的互感器。它利用铁心线圈中铁心受直流和交流电流共同磁化时的非线性和非对称性,通过整流电路,将通过线圈的直流大电流按匝数反比变换成直流小电流。主要用于测量直流大电流,也在整流系统中用作电流反馈、控制和保护元件。与分流器(见电流表)比较,它的电能损耗低并具有隔离作用。常用的直流电流互感器的线路如图。图中A与B是两个相同但各自独立的铁心。直流大电流I1流过两个初级绕组(即图中的穿通导线,相当于初级N1=1匝),两铁心上的次级绕组均为N2匝,以相反极性串接,由正弦波交流电源供电。随着电源电压极性交替变换,两铁心将轮流处于深饱和与非饱和状态。在理想条件下,电源电压U与负载电阻Rx上电压之差,由非饱和铁心上的次级绕组承担,并有N1I1=N2I2或I1/I2=N2/N1(I2为次级电流),即I2和I2与匝数有反比关系。I2经整流后,可用直流电流表读出,或利用负载电阻Rx上的电压降计算出。
  
  20世纪30年代后,由于用了附加的补偿绕组,使直流电流互感器的准确度提高到 0.1级。随着电子器件的发展,利用铁心磁通中的偶次谐波分量,经过放大、反馈形成自动补偿式的零磁通直流互感器,其误差低于0.01%。
  

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条