说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 液气两相流
1)  liquid-gas two-phase flow
液气两相流
2)  gas-liquid two-phase flow
气液两相流
1.
Simulation of effects of hydrophilic properties of channel walls on characteristics of gas-liquid two-phase flow in anode channel of DMFC;
壁面亲水性对DMFC阳极通道内气液两相流影响的数值模拟
2.
Numerical simulation of gas-liquid two-phase flow in aeration basin;
曝气池中气液两相流数值模拟
3.
Metering characteristics of slotted-orifice for gas-liquid two-phase flow with low liquid fractions;
槽式孔板的低含液率气液两相流测量特性
3)  gas-liquid flow
气液两相流
1.
Hydrodynamic characteristics of gas-liquid flow in an up-flow ejector;
上喷式喷射器内气液两相流的流体力学特征
2.
Numerical simulation on the gas-liquid flows inside the oil-gas Separators;
油气分离器内气液两相流的数值模拟
3.
CFD simulation of gas-liquid flow in bubble column;
鼓泡塔反应器气液两相流CFD数值模拟
4)  gas/liquid two-phase flow
气液两相流
1.
Symbolic sequence statistical analysis of differential pressure measurement fluctuating signal of gas/liquid two-phase flow;
气液两相流差压测量波动信号的符号序列统计分析
2.
Wigner-Ville analysis of measurement fluctuating signals of conductance sensor in gas/liquid two-phase flow;
气液两相流电导传感器测量波动信号的Wigner-Ville分析
3.
Study on Analysis Method of Dynamic Fluctuating Signal of Gas/Liquid Two-Phase Flow;
气液两相流动态波动信号分析方法研究
5)  two-phase flow
气液两相流
1.
Numerical simulation of three dimensional gas/liquid two-phase flow in a proton exchange membrane fuel cell;
质子交换膜燃料电池三维气液两相流数值模拟
2.
Model research of full hole two-phase flow in underbalanced horizontal well drilling;
欠平衡钻水平井全井段气液两相流模型研究
3.
In this paper,hot-film anemometer with X-type probe is applied to the measurement of gas-liquid two-phase flow on a sieve tray.
实验测定塔板上气液两相流的流动特性 ,可以为数学模型中参数的确定、模型的验证以及工程设计提供实验依据 。
6)  gas-liquid two-phase flow
气-液两相流
1.
Study on the characteristics of the fluctuating pressure for gas-liquid two-phase flow across the circular cylinder surface;
气-液两相流横掠圆柱表面脉动压力特性的研究
2.
Its basic principle is that there is a quite steady flow state of annular flow in the flow pattern of gas-liquid two-phase flow.
模型是建立在压力能量消耗率最小的原理上的,其基本原理是:在气-液两相流的流型中,环状流具有相当稳定的流动状态。
补充资料:传热学:两相流换热
两相流换热:
自然界中的物质有3种形态﹕固相﹑液相和气相。两相物质共存的流动称为两相流。两相流与管道壁面之间的传热过程称为两相流换热﹐它实际上也是一种对流换热。在工业生產中﹐有各种各样的两相流和两相流换热。例如﹐在化学工业中的流化床内的流动和换热﹐用管道输送粉状和粒状固相物质时的流动和换热﹐气-液(或汽-液)两相流换热等。其中汽-液两相流换热得到广泛而深入的研究﹐因为它是生產中广为使用的蒸汽锅炉﹑蒸汽冷凝设备和核反应堆中传热计算的重要基础知识。两相流换热已发展成为传热学的一个重要分支。
         两相流换热与单相流换热的主要区别在於两相分界面的形状对流型和换热过程有重要影响﹐而相分界面的形状又随著含汽率﹑流速和管道放置的方位等条件的变化而改变。例如对於竖管的两相流传热就有4种流态(见图 竖管内两相流换热示意图 )。泡状流﹕当含汽率不大时﹐在连续液体中均匀分布著许多大小不同的小汽泡。块状流﹕当含汽率增高到某一数值时﹐许多小汽泡就汇集成为一个块状的大汽泡﹐其直径接近管道的内径。在大汽泡之间的液体中含有一些均布的小汽泡。环状液膜流﹕当含汽率增高到很高时﹐液相变成沿管壁流动的环状液膜﹐而汽相则居中流动﹐少量液相以细小雾状液珠悬浮在汽相中。雾状流﹕当管壁上的环状液膜被全部蒸发时﹐管内就充满著悬浮雾滴。
         进行两相流换热计算时﹐必须根据不同的流型和含汽率的高低﹐引用相应的经验公式。常见的两相流换热有沸腾换热和凝结换热。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条