1) EFI Engine
电喷发动机
1.
Fault Diagnosis of Fuel Pressure and Fuel Supply System of EFI Engine;
电喷发动机燃油压力与燃油供给系统故障诊断
2.
Basic principle and attentions of EFI engine′s fault diagnosis;
电喷发动机故障诊断的基本原则及注意事项
3.
In view of the defect of traditional failure protection function,a fault-tolerant control model for a specific EFI engine is set up,using master and distributed neural networks based on extended back propagation algorithm(EBPA).
针对传统的失效保护功能的缺陷,提出使用基于改进BP神经网络算法的主从神经网络建立某型电喷发动机的容错控制模型。
2) electronic fuel injection engine
电喷发动机
1.
Analysis and troubleshooting of electronic fuel injection engine idle speed instability;
电喷发动机怠速不稳故障的分析与排除
2.
To detect the electronic fuel injection engine by using the intake air;vacuum instrument;
利用进气真空表检测电喷发动机
3.
Realization of electronic-controlled system for electronic fuel injection engine on eddy dynamometer;
电喷发动机电控系统在发动机台架上的实现
3) electrical ejection engine
电喷发动机
1.
Development of an expert system for fault diagnosis of electrical ejection engines;
电喷发动机故障诊断专家系统的研究
2.
In view of the shortcomings of traditional expert systems,this paper presents the application of artificial neural network technology in the fault diagnosis of electrical ejection engine.
基于传统专家系统存在的缺点,文中以人工神经网络技术在电喷发动机故障诊断方面的应用为基础,以MATLAB7。
3.
In order to train the thought of students to diagnose the fault of electrical ejection engine and the ability on fixing the breakdown of electrical ejection engine,a demonstrating system based on visualized technology was developed by means of KINGVIE 6.
为培养学生对电喷发动机故障诊断的思路和排除的实际能力,以组态王工业控制软件为开发平台,研制开发出基于图形化技术的电喷发动机故障诊断教学系统,该系统具有在线教学、仿真教学和自动评分考核等功能。
4) electronic ejection engine
电喷发动机
1.
Fault diagnosis for electronic ejection engine using MATLAB software package;
基于MATLAB软件包程序的电喷发动机故障诊断
2.
A model of electronic ejection engine fault diagnosis based on RBF network has been set up by using measured from fixed-check as learning example.
阐述了神经网络的模型、算法和分类,利用电喷发动机实测数据作为学习样本,采用径向基函数神经网络建立发动机的故障诊断模型,通过该模型对电喷发动机的参数进行了辨识,表明RBF网络学习速度很快,适于在线实时监测与诊断。
3.
The Radial Basis Function neural network with some fault samples of electronic ejection engine is trained and the neural network model is applied to identify the samples to be identified.
以RBF网络为识别模型,对电喷发动机的故障进行训练,并应用于待识别故障样本的识别仿真。
5) FAI electronic fuel supply system
FAI电喷发动机
6) 2.4S electronic injection engine
2.4S电喷发动机
补充资料：厂用电受电
厂用电受电
energizing of auxiliary power system
chongyongd一on sho一Jd一on厂用电受电(energizing of auxiliary powersystem)机组附属设备安装完毕后需通电试运行，所需厂用电源由外部供给，因此厂用电受电是调试工作开始的标志。 受电步骤新建电厂先由电力系统向变电站供电，再依次对高压起动/备用变压器、3~10kv厂用配电装置、厂用工作变压器及380V配电装置供电。扩建电厂因高压起动/备用变压器已经投人运行，故可利用它的电源对扩建的厂用配电装置等供电。 调试项目主要有:①用额定电压依次对空载线路、变电站母线、隔离开关、断瘩器、互感器、变压器及厂用配电装置等进行冲击合闸试验。有条件时.冲击合闸前应先进行递升加压试验。升压过程中注意检查各设备有无放电声及短路现象，发现问题及时处理后再进行升压。②检查三相电压应平衡，相序应正确，各段母线的相位彼此应一致。对配电装置供电时，有时会由于母线电容和与母线连接的电磁式电压互感器的电感相互作用而出现铁磁谐振，此时相电压升高，中性点明显位移。为消除谐振可在电压互感器的剩余电压绕组处并联电阻以去振。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条