说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 叶轮损失模型
1)  impeller loss model
叶轮损失模型
1.
In view of the discrepancy of current loss models of centrifugal compressor,the way of adopting polytropic coefficient instead of adiabatic exponent in the process of calculating parameters of all sections was put forward on the basis of summarizing impeller loss models of centrifugal compressor.
针对目前离心压缩机损失模型的差异性,在总结离心压缩机叶轮损失模型的基础上,提出在计算各截面参数时采用多变系数替换绝热指数的方法。
2)  profile loss
叶型损失
1.
The test results show that,for this static cascade,using the aft-loaded profile and curved blade can not only reduce the profile loss,but also weaken the secondary flow.
实验结果表明采用后部加载叶型和弯叶片设计可以有效地减少叶型损失和二次流损失;同时变冲角性能得到极大改善,在±10°冲角范围内总流动损失系数变化不超20%,可以肯定该叶片改型设计是成功的。
2.
With the aid of a large database of measured profile losses,including in-house results and recent cases from the open literature,the profile loss predictions of Kacker and Okapuu have been improved.
借助于内部试验和公开发表的大量的叶型损失试验数据,在Kacker和Okapuu的叶型损失预测模型的基础上,提出一种改进的损失预测模型。
3.
Further,the impact of boundary layer separation and wake vortices on profile loss were analyzed.
对边界层分离和尾迹涡产生叶型损失的原因进行了分析,结果表明:尾迹涡的扰动作用使得成核过程发生了变化,且改变了水滴数和湿度的分布。
3)  loss model
损失模型
1.
On the basis of summarizing the current ways of performance forecast for centrifugal compressor,put forward the way of adopting polytropic coefficient instead of adiabatic exponent in the process of calculating the compressor s energy loss models and parameters of all sections.
在总结目前离心压缩机性能预测方法的基础上,提出在计算压缩机损失模型和各截面参数时采用多变系数替换绝热指数的方法。
2.
The paper provides a suit of loss models about calculating design and off-design points.
提出了一套计算设计点及非设计点的损失模型,应用所提出模型对某型对旋式轴流通风机的性能特性进行预测计算,计算结果与样机试验测试结果对比,效果良好。
3.
Based on the experimental data of a 99 mm rotor,various losses and loss models of the stator of variable geometry radial inflow turbine(VGT) was analyzed.
基于99 mm叶轮实验,分析了变几何径向透平静叶的各种损失以及不同的损失模型。
4)  impeller friction losses
叶轮摩擦损失
1.
In this paper,the mathematical model of impeller friction losses is deduced.
推导了叶轮摩擦损失的数学模型,针对与之相关的众多结构参数,采用正交试验的方法,对各影响因素进行优化分析,找出了影响叶轮摩擦损失的关键结构参数,并比较其影响的显著性。
5)  profile loss
型面损失,叶型损失
6)  phosphorus loss model
磷损失模型
补充资料:AutoCad 教你绘制三爪卡盘模型,借用四视图来建模型
小弟写教程纯粹表达的是建模思路,供初学者参考.任何物体的建摸都需要思路,只有思路多,模型也就水到渠成.ok废话就不说了.建议使用1024X768分辨率

开始
先看下最终效果




第一步,如图所示将窗口分为四个视图




第二步,依次选择每个窗口,在分别输入各自己的视图




第三步,建立ucs重新建立世界坐标体系,捕捉三点来确定各自的ucs如图




第四步,初步大致建立基本模型.可以在主视图建立两个不同的圆,在用ext拉升,在用差集运算.如图:




第五步:关键一步,在此的我思路是.先画出卡爪的基本投影,在把他进行面域,在进行拉升高度分别是10,20,30曾t形状.如图:




第六步:画出螺栓的初步形状.如图




第七步:利用ext拉升圆,在拉升内六边形.注意拉升六边行时方向与拉升圆的方向是相反的.
之后在利用差集运算





第八步:将所得内螺栓模型分别复制到卡爪上,在利用三个视图调到与卡爪的中心对称.效果如图红色的是螺栓,最后是差集




第九步:阵列




第10步.模型就完成了




来一张利用矢量处理的图片


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条