说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 免拆保温墙模
1)  heat preservation formwork
免拆保温墙模
1.
The presentation of the slitted shear wall structure with the heat preservation formwork has blazed a new way in the development of energy saving building system.
免拆保温墙模复合剪力墙的研发为保温节能住宅的发展开辟了新的道路。
2)  moulding board
免拆墙模
1.
Research on characteristics about complex shearing wall system with moulding board;
免拆墙模复合剪力墙体系的特性
3)  insulated wall formwork
保温墙模
1.
The construction of insulated wall formwork composite shear wall structure in low temperature
保温墙模复合剪力墙结构在低温条件下的施工
4)  complex shear walls system without demoulding board
免拆墙模复合剪力墙
1.
Research on anti-seismic performance of complex shear walls system without demoulding board;
免拆墙模复合剪力墙构件抗震性能的研究
5)  thin shear wall without demoulding
免拆模薄壁剪力墙
1.
Based on the traditional shear wall, a new residential structure system -thin shear wall without demoulding of reinforced concrete is advanced in this paper.
在此情况下,本文基于普通剪力墙的概念,提出了一种新型的住宅体系—免拆模薄壁剪力墙复合体系,旨在探索一种能替代传统的砖混结构的建筑体系。
6)  stay-in-place mould
免拆模板
1.
Application of stay-in-place mould in construction of composite concrete shear walls;
浅谈免拆模板复合剪力墙体系在施工中的应用
2.
Composite shear wall system and mechanical properties of GRC stay-in-place mould;
复合剪力墙体系及GRC免拆模板力学性能
补充资料:拆模-----分模面
1.分模面的定义
     分模面是指分开模具取出产品和浇注系统凝料的可分离的接触表面。一副模具根据需要可能一个或两个以上的分模面,分模面可以是垂直于合模方向,也可以与合模方向平行或倾斜。
  2.分模面的形式
    从分模面的数目来看,有单分模面,双分模面,多分模面。
    从分模面的形状来看,平面,斜面,阶梯面,还有曲面。(如下图)


 



 




 1.考虑产品的质量
    (a).确保产品尺寸精度
    对于有同轴度要求的产品,应全部在动模或在定模成型。如果分别在动模或定模内成型,则会因模具合模不准确而难于保证其同轴度要求。
    选择分模面时,应考虑减小由于脱模斜度造成产品的大小端尺寸差异。如果产品较高,若型腔设在动模的一侧,则因脱模斜度造成产品的大小端尺寸差异较大,当产品不允许有较大脱模斜度时,采用此种结构必然使脱模困难。若产品外观无严格要求,可将分模面选在产品中间,它可以采用较小的脱模斜度,有得于脱模

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条