1) collimated laser
准直激光
1.
A new method based on the traditional method is presented,applying the collimated laser to simulate the axes of the multi-barrel launcher.
在传统测试方法的基础上,采用准直激光光束模拟多管火箭发射器炮管轴线,利用CCD成像系统,结合数字图像处理技术完成了对多管武器系统的平行度检测,很大程度上弥补了传统测试方法的不足。
2) laser collimation
激光准直
1.
Study of large diameter measurement system with laser collimation;
基于激光准直瞄准的大直径测量系统的研究
2.
In order to realize synthetic coaxiality measurement for position deviations and angle deviations simultaneously,a laser beam-spot receiver system consisting of a receiver lens,beam splitter prisms,and CCD based on laser collimation was established.
为了实现在同轴度测量中平行偏差(平偏)和倾斜偏差(角偏)两个量的同时测量,建立了基于激光准直性的光斑接收系统。
3.
Based on the principle and technology of laser collimation and optoelectronic inspection, an optoelectronic measuring method is presented to measure the straightness of the bore with a diameter of 25 mm by using the quadrant detection method, technique of laser collimation, optoelectronic detection, precision machine, servocontrol and computer for reference.
基于激光准直和光电探测原理与技术,并借鉴象限探测法、精密机械、伺服控制技术和计算机技术研制了一种用于Φ25mm火炮身管直线度的光电测量系统。
3) laser alignment
激光准直
1.
Design of laser alignment measuring system for guide rails assembling in situ;
双轨安装现场激光准直测量系统的设计
2.
Analyzing characteristic of the four-quadrant detector applied to laser alignment;
四象限探测器用作激光准直的特性分析
3.
Application of wireless USB data transmission system in laser alignment-instrument measurement;
无线USB数据传输系统在激光准直仪测量中的应用
4) laser collimator
激光准直仪
1.
The principle of portable laser collimator is introduced in this paper and its laser device,PSD signal processing circuits data acquisition are analysed in detail.
本文介绍了便携式激光准直仪的工作原理 ,分析了激光器、PSD信号调理电路及数据采集处理系统的设计。
2.
A new automatic measuring system of alignment error portable laser collimator is introduced.
介绍了一种新颖的直线度误差自动测量系统———便携式激光准直仪。
5) laser auto-collimation
激光自准直
1.
Based on the theory of perspective projection transformation,a new modeling method for laser auto-collimation angle measurement system is proposed.
基于透视投影变换,提出了一种新的激光自准直测角系统建模方法,通过对系统安装误差因素和模型外参数的仿真分析,提出了一种带有内外参数的激光自准直简化测量模型,为激光自准直测角系统建模、标定等问题的解决提供了一个有效的理论依据,具有一定的理论意义和工程实际应用价值。
6) laser aligner
激光准直仪
1.
For coordinate transfer of control points of oblique super high-rise buildings with high accuracy and precision,methods combining the electronic tachometer with laser aligner were adopted.
对于倾斜超高层建筑高精度的控制点坐标传递,采用全站仪与激光准直仪相结合,在楼层上多次分段转折投测,逐段接力将控制点坐标传递到顶层控制点。
补充资料：激光准直仪
激光准直仪
laser collimator
iiguang Zhunzhiyi激光准直仪(laser Collimator)利用激光束标定直线的仪器。通常由激光发射系统和光电检侧系统组成。其原理是:利用激光的方向性好、发散角小、亮度强等特点，通过望远镜作定向发射，在空间形成一条光束作为准直的墓准线。分为激光经纬仪准直和波带板激光准直。激光经纬仪准直，由望远镜发射器和光电检测器(光电接收靶)组成。激光通过望远镜发射，调节焦距使光束能在接收靶上形成较小的光斑，在需要准直的点上用光电检测器观测光斑能量中心，以测定各点偏离基准线的偏差值。激光束受本身的漂移和大气条件的影响，准直精度约为长度的10一5一10一“。用于军用坑道和飞机洞库等地下工程开挖、管道敷设、建筑物施工等。波带板激光准直仪，由激光器点光源、波带板装置与光电接收靶组成。测量时，在基准线两端点上分别安置激光器和接收靶，在中间需要准直的点上安置波带板，激光器l掖光源发射出一束激光，照射到波带板，在接收处由于光干涉作用聚焦形成亮点或亮十字线。根据光的衍射原理，激光发射中心、波带板中心及成像光斑中心将构成一条直线。三点准直克服了漂移，能提高准直精度，若让激光束穿过真空管道，还可克服大气折射影响，准直精度达长度的10一7。用于军事工程长距离精密准直测量，例如导弹发射用的火箭橇轨道、高能粒子对撞机直线加速器、大型机械设备轴线安装及建筑物变形观测等。 (于来法)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条