说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 正交耦合误差
1)  quadrature coupling error
正交耦合误差
2)  cross-coupling error
交叉耦合误差
1.
We innovatively integrates two-dimensional plate scanner with one-dimensional feedback controller,which effectively overcomes the nonlinear cross-coupling error between Z feedback control and XY scan plane in the traditional scanner,and furthermore guarantees the stability of detection beam path with large scan range.
该系统创新地把二维平板扫描器和一维反馈控制器相结合,有效地克服了传统扫描器Z向反馈控制与XY扫描平面之间的非线性交叉耦合误差,同时保证了大范围扫描时检测光路的稳定性。
3)  Coupling error
耦合误差
1.
A new multi-motor synchronization control strategy for lifting platform based on the pulling force balance dead zone error and the center coupling error(PFBDZE-CCE) is proposed.
提出深水试验水池大型升降平台多电机同步协调控制系统构成方案,并提出一种新的基于拉力死区误差均衡及中心耦合误差的升降平台多电机同步协调控制策略,实现了拉力控制和位置控制的解耦;同时,提出了多电机控制的升降平台仿真系统,其仿真结果表明:所提出的控制策略同步稳定性能高、收敛速度快,具有很高的应用价值。
2.
This paper concentrates on the designing method of closed loop system of vibratory gyro based on analysis of the coupling error of vibratory gyro.
在分析振动耦合误差的基础上,提出了振动陀螺仪闭环控制系统的一般设计方案。
4)  quadrature error
正交误差
1.
Analysis and simulation of quadrature error on MEMS gyroscope;
MEMS陀螺正交误差分析与仿真
2.
The reasons for inducing quadrature error and offset error are analyzed and the expressions of quadrature error and offset error are induced.
分析了正交误差和失调误差产生的原因,推导了正交误差和失调误差的表达式。
3.
Aiming at quadrature error, this dissertation proposes an innovative solution, and performs theoretical and experimental studies.
本文以提高微机械陀螺的性能为目标,针对由工艺误差引入的正交误差进行了研究,并设计了电路实现正交误差的补偿消除。
5)  Cross Coupling of Angle Error Voltage
角误差电压交叉耦合
6)  cross coupling errors
[电信]交叉耦合误差
补充资料:Fourier级数(关于正交多项式的)


Fourier级数(关于正交多项式的)
rthogonal polynomials) Fourier series (in

F血的er级数(关于正交多项式的)【I饭的er sedes(加川如卿.1州ylm血‘);。”晓p,八(no opTOroHa‘-眼M,。oro呱。aM)] 形式为 艺。。p。(l) 月之0的级数,其中{尸。}是在区间(a,b)上关于权函数h正交的多项式系(见正交多项式(ort加即间即妙-no而alS)),系数{。。}由公式 b a。一J儿(*)f(*)尸。〔二)、(2)给出.这里,f属于函数类L:=L之f(a,b),h],即它的平方在正交性区间(a,b)上关于权函数h可和(玫比g比可积). 对任意正交级数,(l)的部分和{s。(x,f)}是f的依L:度量的最佳逼近,且a,满足条件 浊a。=0·(3)在证明级数(l)在一个点x或在(a,b)中的某个集合上收敛时,通常利用等式f(x)一s。(戈,f)=拜。汇a。(甲二)只十;一a。+:(价二)只(x)l,其中{a。(叭)}是辅助函数毋二的Founer系数,对于固定的x, 川门=力匕2二丛兰上.。。(。.bl. X一汇而拼。是由Cll南.川回{抽均.以公式(Ch由toffel一Dar·boux fonn“巨)给出的系数.如果正交性区间[a,b]有限,毋乒几且序列笼只圣在给定的点x有界,则级数(l)收敛到值f(x). 对于f6L一L:l(a,b),h」,即在区间(a,b)上关于权函数h可和的函数类,也可定义系数(2).对有限区间!a,b],如果f“L,【(a,b),hl且序列{凡}在整个区间[a,b]上一致有界,则条件(3)成立.在这些条件下,在点x可a,bJ处如果叭〔L,I(a,b),h],则级数(l)收敛到值f(x). 设A是区间(a,b)中的某个集合,序列王尸。}在A上一致有界,设B=[a,b〕\A,记L,(A)‘L,【A,川是在A上关于权函数h的p次可和的函数类.如果对固定的x已Al,有叭任L,(A)及叭。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条