说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 再热汽温
1)  reheat steam temperature
再热汽温
1.
Application of active disturbance rejection to reheat steam temperature control systems;
自抗扰技术在再热汽温控制系统中的应用
2.
In tangential combustion system,the reheat steam temperature can be adjusted by changing burner nozzle angle to just the flame position.
在切向燃烧系统中,通过改变燃烧器喷口的角度可以调节炉内火焰中心位置,可达到调节再热汽温的目的。
3.
By the combined use of a prediction control and PID controller in the control of a reheat steam temperature system.
对混沌优化理论在控制过程中的应用进行了研究:将预测控制和PID控制器结合运用于再热汽温系统的控制当中,并采用神经网络作为系统预测模型,通过混沌优化算法对PID参数实行在线优化。
2)  reheated steam temperature
再热汽温
1.
Chaos optimization-based parameter optimization of predictive PID controllers for reheated steam temperature;
基于混沌优化的再热汽温预测PID控制器参数优化
2.
In order to solve the control problem of reheated steam temperature system with long inertia times and long time-delays,the model reference adaptive predictive control(MRAPC) method is applied for reheated steam temperature control system of 3# unit in Jingneng Thermal Power CO.
为了解决火电厂大惯性、大时滞的再热汽温控制难题,采用了模型参考自适应预估控制方法,在京能热电公司3号机组再热汽温控制系统得到了的成功应用。
3.
Through a series of retrofitting of the reheated steam spraying water control system and the titling burner control system, with the application of the KPA optimizing control technology and adjusting control parameters by building testing model, the variation of the reheated steam temperature are controlled in smallest scooe.
介绍了河北省张家口发电厂4号机组再热汽温调节系统存在的问题及其影响因素。
3)  reheat temperature
再热汽温
1.
Because the reheat temperature is lower and the stack gas temperature is higher in Hefei Station No.
针对合肥电厂4号锅炉再热汽温偏低,排烟温度过高的问题,确定了在转向室增加再热器受热面的改造方案,根据现锅炉的运行资料,通过热力计算,确定了合适的计算、传热系数等,增加有效受热面积约1076m2,能有效地提高再热汽温和降低排烟温度。
2.
For reheat temperature system, a novel internal model controller with decoupling is provided.
对一类有多变量、强耦合、大时滞特点的再热汽温系统,提出一种新型内模解耦控制器。
3.
Now it has been successfully applied to reheat temperature control system in power plant.
针对一类大迟延惯性时变对象 ,基于现场应用特点提出一种仿人智能控制策略 ,该方法模拟人脑的智能识别和智能决策 ,对复杂不确定系统进行有效控制 ,在电厂再热汽温控制中得到成功应用。
4)  heat and reheat steam temperature
主再热汽温
5)  Reheat steam temperature control
再热汽温控制
6)  temperature of boiler reheat
锅炉再热汽温
补充资料:动力机械:锅炉汽温调节

在运行过程中﹐将锅炉过热器和再热器出口处的蒸汽温度维持在规定限值范围内的手段。在运行时﹐锅炉的负荷﹑燃料的种类和特性﹑给水温度﹑燃烧用的空气量与燃料量的比例﹐以及受热面上积灰程度等因素都会影响过热蒸汽(主蒸汽)和再热蒸汽温度﹐如不加以调节﹐汽温会有较大的波动。现代大型锅炉能自动调节汽温。如果锅炉出口处的蒸汽温度比设计值低﹐就会使汽轮机装置的热效率下降﹐偏低量过大时还会加剧汽轮机末级叶片的水滴侵蚀作用。如汽温比设计值高﹐则会降低过热器和再热器材料的强度和寿命。电站锅炉通常在70~100%负荷范围内﹐只允许汽温在设计值的-10~+5℃的偏差范围内波动。


常用的汽温调节方法有减温器调温﹑摆动燃烧器调温﹑烟气再循环调温﹑烟气挡板调温和汽-汽热交换器调温等。在一台锅炉中可同时采用数种汽温调节方法。


减温器调温 用冷却水直接或间接冷却蒸汽﹐通过改变水量调节蒸汽温度。减温器可分为表面式(间壁式)和喷水式两种。表面式减温器是一种管壳式换热器﹐其特点是冷却水与蒸汽不直接接触。它普遍用在中﹑低压锅炉中。喷水式减温器(图1 喷水式减温器 )将水直接喷入蒸汽中使蒸汽降温﹐与表面式减温器相比具有结构简单﹑调节灵敏﹑调温能力大等优点﹔但对冷却水的品质要求较高﹐一般采用锅炉给水作


为冷却水水源。在高压以上的锅炉中给水品质较好﹐故普遍采用喷水式减温器。 摆动燃烧器调温 将摆动燃烧器喷口向上或向下摆动﹐以改变火焰中心位置的高度﹐从而改变炉膛出口烟气温度和过热器﹐再热器的吸热量﹐以达到调节汽温的目的。燃烧器向上摆时﹐火焰中心升高﹐蒸汽温度提高﹔反之﹐蒸汽温度降低。这种燃烧器一般装于炉膛四角﹐燃烧器上下摆动倾角的幅度为±(20°~30°)﹐调节灵敏﹐倾角每改变1°能使蒸汽温度改变2℃左右。 烟气再循环调温 利用再循环风机将部分低温的烟气(通常是省煤器后的烟气)﹐送入炉膛底部﹐使流经过热器﹑再热器的烟气流量发生变化﹐从而改变炉膛﹑过热器和再热器相互间的吸热量比例﹐以达到调节汽温的目的。这种方法主要用在汽温低于设计值时提高蒸汽温度。再循环烟气会使炉膛温度降低﹐因而对于难着火的煤种易引起燃烧过程不稳定﹐同时会增加燃料不完全燃烧的热损失。对于多灰的燃料﹐它还会引起锅炉部件过分的磨损。


烟气挡板调温 图2 装有烟气挡板的锅炉 为装有烟气挡板的锅炉示意图。锅炉的尾部烟道分隔成2个或3个并列的烟道﹐在各个烟道中分别布置不同的锅炉受热部件﹐在其出口处设置烟气挡板。利用挡板改变各并列烟道中的烟气流量﹐达到调温的目的。这种调温方法对燃料品种的适用范围较广﹐既可提高也可降低汽温﹐但调温惰性较大。


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条