1) loss of electricity
损耗电量
2) loss current measurement method
损耗电流测量法
1.
Then, it introduces a new integrated monitoring method consisting of the DC component method, AC superimoposition method and loss current measurement method, including the construction, key technology and technical paths of the on-line monitoring system.
本文首先介绍了交联聚乙烯绝缘电力电缆各种检测方法 ,然后详细介绍了由“直流分量法”、“交流叠加法”和“损耗电流测量法”三者结合起来的综合判断方法 ,其中包括在线测量系统的构成、关键技术、技术路线等。
2.
In this paper,a comprehensive method combined by DC component method , AC superposition method and loss current measurement method are described at first .
首先介绍了由“直流分量法”、“交流叠加法”和“损耗电流测量法”三者结合起来的综合判断方法,然后重点论述了交流叠加法的具体实现方案。
3) Whole electric energy loss component
全电能损耗分量
4) capacitor loss measuring instrument
电容损耗测量仪
5) energy consumption
能量损耗
1.
Analysis of energy consumption in blank holding of single-action deep-drawing hydraulic press;
单动拉深液压机压边能量损耗分析
2.
By analysing hydraulic system of motorized wheel dump truck, the model of energy consumption is set up.
通过对电动轮自卸车液压系统的分析,建立系统能量损耗模型,并进行计算仿真,可以得出这种系统的能量损耗主要是单向阀的泄漏损失,单向阀的泄漏流量是影响能量损耗的主要参数,而与蓄能器的容积无关,并且得出系统保压时间为60秒。
3.
Analyzed the minimum theory and the theories of DC electric power drag system ,the mathematics model of the energy consumption is built, the optimization answer of controls parameter used by armature electric current is resolved according to the minimum theory, and the feasibility of the minimum energy consumption is analyzed .
在分析了极小值原理和直流电力拖动系统的基础上 ,建立了与能量损耗有关的数学模型 ,利用极小值原理解出了以电枢电流为控制量的最优解 ,并对最小能量损耗控制的可行性进行了分
6) loss modulus
损耗模量
1.
It was concluded that the elastic modulus G′, loss modulus G″ and dynamic viscosity η~ of PLA and its copolymers increases with the increasing of the molecular weight.
结果表明,随着分子量的增加,聚乳酸及其共聚物熔体的弹性模量G′、损耗模量G″及动态黏度η*大幅度地提高,出现假固态行为;分子链柔性较好的共聚组分PEG的引入降低了共聚物熔体的G′、G″及η*;聚合物分子量的多分散性导致聚合物熔体的流动出现了非终端效应;聚乳酸的引入使聚丙烯熔体的G′、G″及η*都有所下降,马来酸酐接枝改性的聚丙烯的引入增大了共混物的G′、G″及η*。
2.
As an application,the scaling exponents of elastic modulus and loss modulus are also obtained.
作为应用,进而得到弹性模量和损耗模量的标度指数。
3.
The effects of the mass concentration and the salinity and the shear angular frequency of the polymer solution on its loss modulus and storage modulus are studied.
为了研究聚合物KYPAM-6A溶液在油藏条件下的黏弹性情况,根据SY5523-2000配置聚合物溶液进行实验,研究质量浓度、矿化度、角频率的变化对溶液损耗模量、储存模量的影响。
补充资料：介质损耗角正切试验(见电容率与损耗因数试验)
介质损耗角正切试验(见电容率与损耗因数试验)
dielectric loss tangent test
)!eZh.sunhooJ一002匕engq一e sh一yon介质损耗角正切试验(dieleetri。1055 tangenttest)见电容率与损耗因数试验。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条