说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 再热汽温控制
1)  Reheat steam temperature control
再热汽温控制
2)  Reheat stream temperature control
再热蒸汽温度控制
3)  reheated steam temperature control system
再热汽温控制系统
1.
Then the algorithm is used in a reheated steam temperature control system of a power plant.
然后将该算法应用于某一电厂的再热汽温控制系统。
4)  reheat temperature
再热汽温
1.
Because the reheat temperature is lower and the stack gas temperature is higher in Hefei Station No.
针对合肥电厂4号锅炉再热汽温偏低,排烟温度过高的问题,确定了在转向室增加再热器受热面的改造方案,根据现锅炉的运行资料,通过热力计算,确定了合适的计算、传热系数等,增加有效受热面积约1076m2,能有效地提高再热汽温和降低排烟温度。
2.
For reheat temperature system, a novel internal model controller with decoupling is provided.
对一类有多变量、强耦合、大时滞特点的再热汽温系统,提出一种新型内模解耦控制器。
3.
Now it has been successfully applied to reheat temperature control system in power plant.
针对一类大迟延惯性时变对象 ,基于现场应用特点提出一种仿人智能控制策略 ,该方法模拟人脑的智能识别和智能决策 ,对复杂不确定系统进行有效控制 ,在电厂再热汽温控制中得到成功应用。
5)  reheat steam temperature
再热汽温
1.
Application of active disturbance rejection to reheat steam temperature control systems;
自抗扰技术在再热汽温控制系统中的应用
2.
In tangential combustion system,the reheat steam temperature can be adjusted by changing burner nozzle angle to just the flame position.
在切向燃烧系统中,通过改变燃烧器喷口的角度可以调节炉内火焰中心位置,可达到调节再热汽温的目的。
3.
By the combined use of a prediction control and PID controller in the control of a reheat steam temperature system.
对混沌优化理论在控制过程中的应用进行了研究:将预测控制和PID控制器结合运用于再热汽温系统的控制当中,并采用神经网络作为系统预测模型,通过混沌优化算法对PID参数实行在线优化。
6)  reheated steam temperature
再热汽温
1.
Chaos optimization-based parameter optimization of predictive PID controllers for reheated steam temperature;
基于混沌优化的再热汽温预测PID控制器参数优化
2.
In order to solve the control problem of reheated steam temperature system with long inertia times and long time-delays,the model reference adaptive predictive control(MRAPC) method is applied for reheated steam temperature control system of 3# unit in Jingneng Thermal Power CO.
为了解决火电厂大惯性、大时滞的再热汽温控制难题,采用了模型参考自适应预估控制方法,在京能热电公司3号机组再热汽温控制系统得到了的成功应用。
3.
Through a series of retrofitting of the reheated steam spraying water control system and the titling burner control system, with the application of the KPA optimizing control technology and adjusting control parameters by building testing model, the variation of the reheated steam temperature are controlled in smallest scooe.
介绍了河北省张家口发电厂4号机组再热汽温调节系统存在的问题及其影响因素。
补充资料:抽汽式汽轮机
      由汽轮机中间级抽出一部分蒸汽供给用户,即在发电的同时还供热的汽轮机。根据用户需要可以设计成一次调节抽汽式或二次调节抽汽式。
  
  一次调节抽汽式汽轮机  又称单抽汽式汽轮机。由高压部分和低压部分组成,相当于一台背压式汽轮机与一台凝汽式汽轮机的组合。新汽进入高压部分作功,膨胀至一定压力后分为二股,一股抽出供给热用户,一股进入低压部分继续膨胀作功,最后排入凝汽器。抽汽压力设计值根据热用户需要确定,并由调压器控制,以维持抽汽压力稳定。单抽汽式汽轮机的功率为高、低压部分所生产功率之和,由进汽量和流经低压部分蒸汽量所决定。调节进汽量可以得到不同的功率。因此,在一定范围内,可同时满足热、电负荷需要。单抽汽式汽轮机在供热抽汽量为零时,相当于一台凝汽式汽轮机;若将进入高压缸的蒸汽全部抽出供给热用户,则相当于一台背压式汽轮机。但实际运行中,为了冷却低压缸,带走由于鼓风摩擦损失所产生的热量,必须有一定量的蒸汽流过低压部分进入凝汽器,所需最小流量约为低压缸设计流量的10%。单抽汽式汽轮机的工况如图所示,它表示出新汽量(Do)、抽汽量(Ce)、电功率(Ni)三者之间的关系;图中Do表示凝汽量,ohh线为抽汽量为零时的凝汽工况线,cdd 线为抽汽量等于新汽量时的背压工况线,在以上两线之间为等抽汽量与等凝汽量工况线,它表示在不同抽汽量下与不同凝汽量下全机电功率与蒸汽流量的关系。在最大抽汽量下汽轮发电机组的最大电功率如图中e点所示;图中如已知Do、De、Do和Ni4个量中的任何两个量,可求得另外两个量。
  
  二次调节抽汽式汽轮机  又称双抽汽式汽轮机。可以同时满足不同参数的热负荷。整个汽轮机分为高、中、低压 3部分。新汽进入高压部分作功,膨胀到一定压力,抽出一部分蒸汽供给热用户;另一部分进入中压部分继续膨胀作功后,再抽出一部分供暖,其余蒸汽经过低压部分排入凝汽器。
  
  双抽汽式汽轮机的工况图是按照一定的典型系统和额定参数绘制的。若汽轮机运行条件不同于绘制工况时,应进行适当修正。调节抽汽式汽轮机各缸均单独设置配汽机构,分别控制各缸进汽量。中、低压缸配汽机构有调节阀和旋转隔板两种形式。功率较小的抽汽机组采用旋转隔板形式有利于设计成单缸结构;高压缸则普遍采用喷嘴调节方式,调节级多数为双列级,以保证有足够大的通流能力。
  
  双抽汽式汽轮机在高、低压缸流量均接近设计值时具有较高的发电经济性。由于热负荷的变化,有时流经各缸的流量差别很大,在某些工况下发电经济性较低。因此,调节抽汽式汽轮机应根据主要热负荷情况进行设计,合理分配各缸流量,以保证长期运行中有较高经济性。合理选定抽汽压力对机组经济性有明显影响,在满足热用户前提下,应尽量降低抽汽压力。早期生产的供暖抽汽机组,抽汽压力为0.12~0.25兆帕,近年已将下限降为0.07兆帕。
  

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条