说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 联结点地震响应
1)  unite node seismic response
联结点地震响应
2)  seismic response of structures
结构地震响应
1.
The correlation between these earthquake intensity indices and the seismic response of structures is studied for elastoplastic SDOF and MDOF systems,and the applicability and characteristics of these earthquake intensity indices are also discussed.
本文参考已有学者的研究成果,总结归纳了现有主要的33个地震动强度指标,基于弹塑性SDOF和MD-OF系统的代表性地震响应指标,分析了不同地震动强度指标与不同结构地震响应指标之间的相关性,研究了不同地震动指标的适用范围和优缺点,给出了结构抗震分析用地震强度指标的建议。
3)  seismic response of base isolated structure
隔震结构地震响应
4)  seismic response
地震响应
1.
Analysis on seismic response of special cavernous structure of carbonate;
碳酸盐岩特殊孔洞型构造地震响应特征分析
2.
Research on petrophysical parameters and seismic response models of He 8 formation;
盒8地层岩石物理参数及地震响应模型研究
3.
Sedimentary facies and seismic responses in the Upper Jurassic Suining Formation,Luodai Gas Field;
洛带气田上侏罗统遂宁组沉积相及含气地震响应特征
5)  earthquake response
地震响应
1.
Non-classical mode superposition method for earthquake response of a reinforced concrete building with a steel tower atop it;
非经典振型分解法求混凝土房屋及其上钢塔的地震响应
2.
Magneto-rheological(MR) dampers semi-active control of earthquake response for elevated bridge;
高架桥梁地震响应磁流变阻尼器(MR)半主动控制
3.
Dynamic property and earthquake response analysis of cable-strut-supported shell structure;
张弦网壳结构的自振特性及地震响应分析
6)  seismic responses
地震响应
1.
Nonlinear seismic responses of arch dams with joins;
带横缝拱坝的非线性地震响应
2.
Study on the Seismic Responses and Shock Absorption Technique of Self-anchored Suspension Bridges;
自锚式悬索桥地震响应分析和减震措施研究
3.
The three dimensional FEM models are constructed to analyze the effects of raft thickness on the vibration characteristics and seismic responses of the twin-towers high-rise building structures with enlarged base,and the dynamic soil-structure interaction is incorporated in the analysis as well.
考虑土-结构动力相互作用,建立了双塔楼大底盘高层建筑动力响应分析的三维有限元模型,研究了筏板厚度变化对结构振动特性和地震响应的影响。
补充资料:闭式单点、双点压力机
代码:00413
设备名称:闭式单点、双点压力机
型号规格:公称力≥800kN
计量单位:台
主要参数内容
国际先进国内先进国内一般国内落后评定方法及说明
(一)加工精度
    参照GB10924-89、GB10933-89、JB5200-91
1、滑块下平面对工作台上平面的平行度(mm)
30%精度储备20%精度储备达到规定值大于规定值 
0.02+0.10/100×滑块下平面的被测长度
     
2、滑块行程对工作台上平面的垂直度
30%精度储备20%精度储备达到规定值大于规定值 
0.05+0.02/100×滑块行程长度
     
(二)结构性能
     
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50%
大于规定值10%大于规定值达到规定值达不到规定值 
2、液压超负荷保险装置、微调装置、吨位指示器
全部具有全部具有部分具有没有 
(三)噪声dB(A)
     
1、公称力≤400kN
≤85≤87≤88>88 
2、公称力>400kN
≤87≤88≤90>90 
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条