1) emitter
[英][i'mitə] [美][ɪ'mɪtɚ]
灌水器
1.
A development method for high anti-clogged drip emitters based on two-phase flow simulations;
基于两相流模拟的高抗堵滴灌灌水器开发方法
2.
Two-phase flow analysis and experimental investigation of micro-PIV and anti-clogging for micro-channels of emitter;
灌水器微细流道水沙两相流分析和微PIV及抗堵实验研究
3.
Computer Aided Design of Runner System for Emitter Injection Mold;
灌水器注塑模浇注系统计算机辅助设计
2) emitters
[英][i'mitə] [美][ɪ'mɪtɚ]
灌水器
1.
Two types of the tiny pressure drip irrigation emitter are placed on the experimental stage in laboratory,and the tiny pressure emitters are carried on experiment at free flow.
在试验室内,对研制的微压灌水器进行了水力性能试验。
2.
This paper summerizes development and application situations of the SDI, and a necessity is put forward to develop emitters that they are possessed of both good pressure-discharge relation and peformance of resistance to negtive pressure with the aim of spreading in nati.
本文对地下滴灌技术的发展及应用现状进行了综述，并讨论了研制出一种既具有良好压力流量关系又可抗负压堵塞能力的灌水器（ 滴头） ，以促进我国推广应用地下滴灌技术。
3.
7% of the emitters can be declared to be clogged with discharge reduced more than 25%,and 2.
以运行2年的日光温室番茄地下滴灌系统为对象,通过对灌水器流量进行测试,分析了滴灌带埋深、施肥次数、施肥量和土壤层状结构等对灌水器堵塞程度及灌水均匀性的影响。
3) irrigator
[英]['irigeitə] [美]['ɪrə,getɚ]
灌水器
1.
Rapid finalization of irrigator dripper in drip-irrigation by virtue of RP technique;
基于RP技术的滴灌用灌水器滴头的快速定型
4) drip emitter
滴灌灌水器
1.
Five different turbulence models provided by current fluid simulation software FLUENT,such as standard k-ε mode1,RNG k-ε model, Realizable k-ε model,standard k-ω model and SST k-ω model,have been used to simulate the flow field of drip emitters in this paper.
采用通用流体模拟软件FLUENT所提供的5种不同的湍流模型:标准k-ε模型、RNG k-ε模型、Real-izable k-ε模型、标准k-ω模型、SST k-ω模型,对滴灌灌水器微流道内流场水流流动进行了数值模拟。
5) Drip emitters
滴灌灌水器
1.
By means of experiment research,water quality standard for drip emitters of Xinjiang Tianye Group Co.
通过实验研究 ,得出了新疆天业 (集团 )公司滴灌灌水器要求的水质标准 ,建立了计算玛纳斯河灌区渠水所含粘粒、粉粒、沙粒的去除率经验公式 ,并根据六宫支渠和西岸大渠水质算出了沉淀池设计表面负荷
6) micro-irrigation emitter
微灌灌水器
1.
An agricultural micro-irrigation emitter is a key device for micro-irrigation, and the hydraulic performance of the micro-irrigation emitter is an important index sign in measuring the quality of micro-irrigation system, it is also an important parameter of the micro-irrigation system design.
供水部分由水泵、仪表、控制阀、过滤器组成;传输部分由干管、支管、毛管组成的管网;执行部分是各种形式的微灌灌水器。
补充资料：电力电容器灌封料
分子式：
CAS号：
性质：树脂(A)为聚醚填充料等，固化剂(B)为改性异氰酸酯等。由聚醚与辅助材料经脱水精制后再加填充料和催化剂进行反应，然后经研磨混合、过滤而成。树脂为白色或黄色黏液。密度1.35～1.40g/cm3。黏度(25℃)7000mPa·s左右。固化剂为黑色或黄色黏液。密度1.10～1.15g/cm3，黏度(25℃)5500mPa·s左右。用于电容器元件特别适用于电力电容器的表面密封和固定。
CAS号：
性质：树脂(A)为聚醚填充料等，固化剂(B)为改性异氰酸酯等。由聚醚与辅助材料经脱水精制后再加填充料和催化剂进行反应，然后经研磨混合、过滤而成。树脂为白色或黄色黏液。密度1.35～1.40g/cm3。黏度(25℃)7000mPa·s左右。固化剂为黑色或黄色黏液。密度1.10～1.15g/cm3，黏度(25℃)5500mPa·s左右。用于电容器元件特别适用于电力电容器的表面密封和固定。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条