说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 动态热应力响应
1)  dynamic thermal stresses response
动态热应力响应
1.
The dynamic thermal stresses responses analysis model problems of metal-ceramic functionally graded materials (FGMs) under thermal shock load are studied.
研究了梯度材料在承受热冲击载荷作用时的动态热应力响应分析模型问题。
2)  thermo dynamic response
热动力响应
1.
This paper establishes a model of heat conduction and thermo dynamic responses of a spherical cavity under shocks of both heat and pressure whose distributions versus time are arbitrary.
以温度和位移为未知变量,建立了当内壁面受到随时间任意分布的热和力联合冲击作用时,含球型空腔无限弹性介质的球对称热传导和热动力响应模型;利用拉普拉斯变换法,导出了温度和位移的封闭解表达式。
3)  dynamic stress response
动态应力响应
1.
The dynamic stress response of the lower course by moving-vibrating compaction on semi-rigid base was analyzed to judge whether it caused early wreckage to the lower course.
为判断半刚性基层振动压实能否造成下承层的早期破坏,对半刚性基层在移动—振动压实荷载作用下的下承层动态应力响应进行分析。
4)  dynamic thermal stress
动态热应力
1.
In this paper, a problem of coupled dynamic thermal stress thermal distribution at the surface of a semicircular cavity in a send-infinite elastic plane was investigated, while a steady temperature field was applied at the surface of the semicircular cavity.
分析了半无限弹性平面内一半圆孔表面施加稳态温度场条件下的半圆孔孔边耦合动态热应力分布问题,利用共形映照等复变函数的方法,得到了汉开尔函数表示此问题的解析解。
5)  dynamic thermal stresses
动态热应力
1.
Study on dynamic thermal stresses in large scale steam turbine rotors;
大型汽轮机转子动态热应力的数学模型
6)  dynamic thermo-elastic response
热弹性动力响应
1.
Thusly, the dynamic thermo-elastic responses of a DMC subjected to rapid arbitrary heating are studied.
最后将离散多层圆筒的热弹性动力响应与单层厚壁圆筒的响应进行了比较,并分析了钢带缠绕倾角和材料参数对热弹性动力响应的影响。
补充资料:动态响应


动态响应
dynamic response

dongto(x}ongying动态响应(dynamie response)控制系统对输人信号从初始状态到最终状态的响应过程。 经常采用的试验输人信号有阶跃函数、斜坡函数、抛物线函数、正弦函数和冲激函数等。这些信号都是简单的时间函数。利用它们可以分析控制系统。单位阶跃函数的表示式为r(t)=O,t<01,t>0单位斜坡函数的表示式为r(t)~0,t<0t,t>O 单位冲激函数的表示式见冲激响应。 图1所示为一控制系统对单位阶跃函数的动态响应过程,图中表明了下列性能指标:C(I) ┌──┐ │/ │ ┌──┴──┼─────────┐│翻 │…芽锭皂厂-谆靛飞%┤├───┐ │i灌…一r--一不飞 │├料┐ │ │{;下{ │·; ││ │ │ │}识} │ │├─┤ │ │l │ ││了│ │ │{ │ ││ │ │ │l吸 │ │├─┴─┼─┼┴──┴─────┘│国 │ │ │ 扣│ │ └───┴─┘ ,之OU 工k曰 : nU几” 图l表示性能指标的单位阶跃响应曲线 (1)延迟时间td:响应曲线第一次达到稳态值的一半所需时间。 (2)上升时间t,:响应曲线从稳态值的10%上升到90%,或从5%上升到95%,或从o上升到100%所需的时间。 (3)峰值时间tP:响应曲线达到过调量的第一个峰值所需的时间。(4)超调量MP:响应曲线的最大偏差值(响应曲线的最终稳态值作为1,以其作为基准)。若响应曲线的最终稳态值不为1,则百分比超调量为C(t。)一C(co)二一二书行一一一二X 100%。 C(co) (5)响应时间ts:系统受到扰动作用后从一个平衡状态到达新的平衡状态所经历的时间,也就是动态过程所经历的时间。一般,当输出量与其稳态值之差达到了而且不再超过一允许误差范围(通常取稳态值的5%或2%)时,认为动态过程结束。 一阶系统的动态响应图2(a)所示为一阶系统的框图,图2(b)为其简化框图。系统的输人一输出关_、,C‘s)]__,、,__、、,,、_,_,、__系为斋书夭一不介下。图2(。)所示为单位阶跃响应,其/J、/节R(s)Ts+l”目“、‘z’/,zJ、,,一尚rj,“\。,二~,二表达式为c(t)一1一e一宁(t妻0)。图2(d)所示为单位斜坡响应,其表达式为c(动一t一T+Te一孚(t》。)。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条