1) overcharge
[英][,əʊvə'tʃɑ:dʒ] [美]['ovɚ'tʃɑrdʒ]
过充
1.
Aimming at the damage and overcharge to Ni-MH battery in the conventional costant-current charging process,fuzzy controller is embedded in the charging process.
针对传统恒流快速充电过程中容易对镍氢电池造成损坏和过充等问题,将模糊控制引入到镍氢电池充电过程,选取电池充电电压u和理想电压u的差ΔV和电压的变化率Δu/Δt作为输入变量建立二维模糊控制器模型。
2.
The explosion of battery results from the heat and pressure accumulation by internal component reactions under abuse conditions,such as overheating,overcharge,short-circuit and so on.
当在热冲击、过充、过放、短路等滥用状态下,电池内部的活性物质及电解液等组分间将发生化学、电化学反应,产生大量的热量与气体,当积累到一定程度就会引起电池的着火、爆炸。
3.
The batteries with the additives could resist overcharge of 3 C,10 V when the content of additive was 5%.
环己基苯和二甲苯作为耐过充添加剂加入锂离子电池电解液中。
2) over-charging
过充
1.
The IC not only achieves the float-charging and the protection of over-charging,over-discharging,and over-discharging current,but also solves the problem of wasting of area which caused by the independent elements.
它既可以实现对免维护铅酸蓄电池的浮充充电及过充、过放、过流保护,也可以解决分立元件构成的电路占用面积大的问题。
3) Over-charging over-discharging
过充过放
4) filling process
充模过程
1.
Numerical simulation on the filling process of water-assisted injection molding;
水辅助注射成型充模过程的数值模拟研究
5) filling process
充型过程
1.
Numerical simulation of inclusion movement in mold filling process of metal melt;
金属液充型过程中夹杂物运动的数值模拟
2.
Study of the factors affecting filling process of grinding ball by vertical centrifugal casting;
立式离心铸造磨球充型过程的影响因素研究
3.
Numerical simulation and experimental verification of the initial temperature distribution of castings during mold filling process;
铸造充型过程初始温度场的数值模拟及实验研究
6) mold filling process
充型过程
1.
Development and application of numerical simulation for the mold filling process of casting;
铸造充型过程数值模拟的研究进展及应用
2.
Numerical Simulation of Mold Filling Process for Wax Pattern in Investment Casting;
熔模精密铸造蜡模充型过程的数值模拟
3.
Numerical simulation equations were established for the mold filling process of liquid metal with turbulent or laminar flows and for the process of liquid metal being solidified and cooled into the casting.
建立了铸件充型过程中金属液流体湍流和层流流动及凝固冷却时三维速度场和温度场数值模拟的计算方程 ;介绍了这些方程的数值求解 ,相关边界条件及凝固潜热处理方法 ;以此为基础 ,编制了三维计算、前处理、后处理程序及相关数据库 ,形成了SRIFCAST软件。
补充资料：过充电
分子式：
CAS号：
性质：蓄电池完全充电后仍延续进行的充电。均衡充电、涓流充电、完全充电后延续的浮充电都是过充电。为确保蓄电池随时处于完全充电状态并均衡一致，过充电是必要的。但是，不加控制的大电流过充电会导致蓄电池过快的析气、失水和温度升高，甚至损坏。
CAS号：
性质：蓄电池完全充电后仍延续进行的充电。均衡充电、涓流充电、完全充电后延续的浮充电都是过充电。为确保蓄电池随时处于完全充电状态并均衡一致，过充电是必要的。但是，不加控制的大电流过充电会导致蓄电池过快的析气、失水和温度升高，甚至损坏。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条